|
|
PDF NCB410U4-DS-A1 Data sheet ( Hoja de datos )
| Número de pieza | NCB410U4-DS-A1 | |
| Descripción | TFT LCD Monitor Control Board | |
| Fabricantes | DATA MODULE | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de NCB410U4-DS-A1 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
For LCD/PDP Monitor (PC, DVI, Video) Interface Controller
For 1280x768, 1366x768, 1600x1200, 1920x1080, 1920x1200 Resolutions TFT LCD/PDP
DATA SHEET
TFT LCD Monitor Control Board
NCB410U4-DS-A1
June 2005
1
1 page  
GENERAL SPECIFICATION
No. Item
Description
WVGA Panel
8520X480
NCB410WV4
XGA Panel
1024X768
NCB410X4
WXGA Panel
1280X768
NCB410W4
1
Model name
WXGA Panel
1366X768
NCB410WZ4
UXGA Panel
1600X1200
NCB410U4
HD Panel
1920X1080
NCB410WH4
WUXGA Panel 1920X1200
NCB410WU4
2 LCD Module
SVGA, XGA, WXGA, SXGA
3 Signal Input
Analog RGB, TMDS(DVI). NTSC/PAL
Resolution
4 Support
H: 31 ∼ 80kHz
V: 55 ∼ 76Hz
5
OSD Control
Plug & Play
Menu, Left, Right, Up, Down, Source, Power
VESA DDC 2B Ver1.3
6 Power Connector
Input
Type: IEC320
Connector
MALE
3Line
7.
Power
Consumption
Supply
Voltage
Max Power
12Vdc/15Vdc/18Vdc or 25Vdc
18W (Without Back Light Inverter)
8 Signal Connector
Analog
Digital
DSUB 15P(R, G, B Separate H, V
Sync)
DVI-D(TMDS)
Video
MINIDIN-4P(SVHS), RCA(CVBS)
Notes 1) Depends On Panel Resolution
- WV : WVGA (850X480)
- X : XGA (1024X768)
- W : WXGA (1280X768)
- WZ : WXGA (1366X768)
- U : UXGA (1600x1200)
- WH : HD 1080i (1920x1080)
- WU : WUXGA (1920x1200)
Note 1)
5 keys
TMDS
5
5 Page 
ASSEMBLY NOTES
This controller is designed for monitors and custom display projects using TFT (active matrix) LCD
panels of 1280x768, 1366x768, 1600x1200, 1920x1080 and 1920x1200 resolutions, PDP panels
of 852x480, 1024x768 and 1366x768 resolutions VGA, SVGA, XGA, WXGA, SXGA, WSXGA and
UXGA signal input. The following provides some guidelines for installation and preparation of a
finished display solution.
Preparation: Before preceding it is important to familiarize yourself with the parts making up the
system and the various connectors, mounting holes and general layout of the controller. As much
as possible connectors have been labeled. Guides to connectors and mounting holes are shown in
the following relevant sections.
1. LCD Panel: This controller has LVDS interface logic on the Board for different kind of TFT LCD
panel. Due to the different signal timing and electrical characteristics from each LCD panel
manufacturer, for selecting LCD interface type and resolution, put jumper marked SW101 on the
right position following LCD panel specification. For selecting DC power level, put jumper marked
J801, J802 on the right position. Supplied power level depends on LCD panel specification.
PDP Panel: This controller has LVDS interface logic on the Board for different kind of PDP panel.
Due to the different signal timing and electrical characteristics from each PDP panel manufacturer,
for selecting LCD interface type and resolution, put jumper marked SW101 on the right position
following PDP panel specification.
2. Controller: Handle the controller with care as static charge may damage electronic components,
Make sure correct jumper and switches settings to match the target LCD and PDP panel
3. LCD connector board: Different makers and models of LCD panel require different panel signal
connectors and different pin assignments.
PDP connector board: Different makers and models of LCD panel require different panel
signal connectors and different pin assignments.
4. LVDS signal cables: In order provide a clean signal it is recommended that LVDS signal cables
should not longer than 30cm. If loose wire cabling is utilized these can be a made into a harness
with cable ties. Care should be taken when you place the cables to avoid signal interface.
Additionally it may necessary in some systems to add ferrite cores to the cables to minimize
signal noise.
5. Inverter: This will be required for the backlight of an LCD, some LCD panel have an inverter
built in. As LCD panels may have 1 or more backlight tubes and the power requirements for
different panel backlights may vary it is important to match the inverter in order to obtain
optimum performance. See application notes for more information on connection
11
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet NCB410U4-DS-A1.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| NCB410U4-DS-A1 | TFT LCD Monitor Control Board | DATA MODULE |
| NCB410U4-DS-AB | TFT LCD Monitor Control Board |  INNODISPLAY |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |