WS3413H Datasheet PDF - WINSEMI
| Part Number | WS3413H | |
| Description | Non-isolated Buck APFC Offline LED Driver | |
| Manufacturers | WINSEMI | |
| Logo |  |
|
|
There is a preview and WS3413H download ( pdf file ) link at the bottom of this page. Total 8 Pages | ||
Preview 1 page No Preview Available !
WS3413H ProductDescription
Features
Internal 650V Power MOSFET
Active PFC for High Power Factor and Low THD
Critical Conduction Mode Operation
System Efficiency up to 95%
Without auxiliary winding
Excellent Line and Load Regulation
±3% LED Output Current Accuracy
Thermal Regulation Function
LED Short/Open Protection
Current Sensing Resistor Open Protection
Auto Fault Recovery
Available in DIP7 Package
Applications
E27 LED Bulb, Spot Light
PAR30, PAR38 Lamp
T8/T10 LED String
Other LED Lighting
Typical Application
Non-isolated Buck APFC Offline LED Driver
Description
The WS3413H is a high precision non-isolated buck
driver with active PFC, specially designed for universal input
offline constant current LED lighting. The driver with on-chip
PFC circuit achieves high power factor and low THD.
Operating in critical conduction mode, the power MOSFET
switching loss is reduced and the inductor is fully utilized.
The WS3413H integrates a 650V power MOSFET. With
few external components, the LED output current can be
precisely controlled.
The WS3413H offers rich protection functions to improve
the system reliability, including LED open circuit protection,
LED short circuit protection, CS resistor open circuit
protection and cycle by cycle current limit. All the protection
functions are auto-recovery. The system reliability is further
improved by the thermal regulation function. The output
current is reduced when the driver is over temperature.
The WS3413H has ultra low start up current and ultra low
operating current.
The WS3413H is available in DIP7 Package.
CopyrigWhINt@SEWMI inMseICmROiMELiEcCroTReOleNcItCroSnics WCIoN.S,ELMtdI .,MAIlCl RriOgEhLtErCeTsReOrNvIeCSd
WINSEMI MICROELECTRONICS
WINSEMI MICROELECTRONICS
1030WINSEMI MICROELECTRONICS
|
| |
 
WS3413H ProductDescription
Application Information
The WS3413H is a high precision Active PFC driver
integrating 650V power MOSFET, specially designed for
non-isolated buck offline constant current LED lighting.
Operating in critical conduction mode, the driver achieves
high power factor, low THD and high efficiency.
Start Up
After system powered up, the VCC pin capacitor is
charged up by the start up resistor. When the VCC pin voltage
reaches the turn on threshold, the internal circuits start
working. The COMP pin voltage is pulled up to 1.5V quickly,
then the WS3413Hstarts switching. The system works at 10k
Hz frequency at the beginning, the COMP voltage rises up
gradually, and the inductor peak current also rises up. The
LED current hence achieves a soft start without overshoot.
After the output voltage is built up, the VCC power is supplied
by the output voltage through a diode.
The maximum value of the startup current is 100uA. For
the application of 85VAC —264VAC, the startup resistor can
be calculated by the equation:
Rst
Vin _ min
I st _ max
85V
100uA
850KΩ
Constant Current Control
The WS3413H utilizes floating ground structure. The
inductor current is sensed during the whole switching cycle,
thus it achieves high precision output current control and also
excellent line and load regulation.
The current in LED can be calculated by the equation:
IO
VCS
RCS
200mV
Rcs
Rcs is the current sensing resistor.
Feedback Network
The WS3413H senses the output current zero crossing
information through the feedback network, the FB falling
threshold voltage is set to 0.2V with 0.15V hysteresis. The FB
pin is also used to detect output OVP, the threshold voltage is
1.6V. The ratio of FB upper resistor to lower resistor can be
set as:
RFBL
RFBL RFBH
1.6V
VOVP
Where,
RFBL: The lower resistor of the feedback network
RFBH: The upper resistor of the feedback network
VOVP: Output over voltage setting point
The minimum VOVP should be set about 1.3Vo.It is
recommended that the FB lower resistor is set to
3.3KΩ—5.1KΩparalleled with a 22pF ceramic capacitor.
Protection Functions
The WS3413H offers rich protection functions to improve
the system reliability.
When the LED is open circuit, the output voltage will
gradually rise up. The output voltage is sensed by the FB pin
when power MOSFET is turned off. When FB voltage reaches
the OVP threshold, it will trigger fault logic and the system
stops switching.
When the LED is shorted circuit, the system will work
under 10k Hz switching frequency. Meanwhile, the output
voltage is low and the VCC pin cannot be charged up by the
output voltage, so the VCC pin voltage will gradually
decrease and finally reaches the UVLO threshold.
After the system enters into fault condition, the VCC
voltage will decrease until it reaches UVLO threshold. Then
the system will re-start again. If the fault condition is removed,
the system will resume normal operation.
When the output is short circuit or the inductor is
saturated, the CS peak voltage will be relatively high. When
CS voltage reaches the internal limitation (1V), the power
MOSFET will be turned off instantaneously. This cycle by
cycle current limitation can help protecting the power
MOSFET, the inductor and the output diode.
Thermal Regulation
The WS3413H integrates thermal regulation function.
When the system is over temperature, the output current is
gradually reduced; the output power and thermal dissipation
are also reduced. The system temperature is regulated and
the system reliability is improved. The thermal regulation
temperature is set to 150℃ internally.
PCB Layouts
The following guidelines should be followed in WS3413H
PCB layout:
www.wWiInNSsEeMmI iM.cICoRmOELTEeClTR: O+N8IC6S-755W-8IN2S5EM0I62M8IC8ROELEFCaTRxO:N+IC8S6-75W5IN-8SE2M5I0 M6I2C9RO9ELECTRONICS
WINSEMI MICROELECTRONICS
WINSEMI MICROELECTRONICS
5/8
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for WS3413H electronic component. |
| Information | Total 8 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ WS3413H.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| WS3413 | The function is Active PFC Non-isolated Buck LED Driver. WINSEMI | |
| WS3413E | The function is Non-isolated Buck APFC Offline LED Driver. WINSEMI | |
| WS3413H | The function is Non-isolated Buck APFC Offline LED Driver. WINSEMI | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
WS34
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||