DataSheet26.com

BA6418N PDF даташит

Спецификация BA6418N изготовлена ​​​​«ROHM Semiconductor» и имеет функцию, называемую «Reversible motor driver».

Детали детали

Номер произв BA6418N
Описание Reversible motor driver
Производители ROHM Semiconductor
логотип ROHM Semiconductor логотип 

5 Pages
scroll

No Preview Available !

BA6418N Даташит, Описание, Даташиты
Motor driver ICs
Reversible motor driver
BA6418N
The BA6418N is a reversible-motor driver with a maximum output current of 0.7A. Two logic inputs allow four output
modes: forward, reverse, stop (idling), and brake. Since logic and power sections have separate ground pins, the IC can
drive speed-variable, reversible motors by connecting an electronic governor circuit.
FFeatures
1) Small standby circuit current.
2) Wide range of operating voltage. (4.5 X 15V)
3) Interfaces with TTL devices.
4) Built-in thermal shutdown circuit.
FBlock diagram
FAbsolute maximum ratings (Ta = 25_C)
462









No Preview Available !

BA6418N Даташит, Описание, Даташиты
Motor driver ICs
FInput / output truth table
BA6418N
FElectrical characteristics (unless otherwise noted, Ta = 25_C, VCC = 9V)
FInput / output circuit (Equivalent circuit)
FApplication example
463









No Preview Available !

BA6418N Даташит, Описание, Даташиты
Motor driver ICs
FThermal derating curve
BA6418N
FOperation notes
(1) The quality of these products have been carefully
checked; however, use of the products with applied volt-
ages, operating temperatures, or other parameters that
exceed the absolute maximum rating given may result in
the damage of the IC and the product it is used in. If the
IC is damaged, the short mode and open modes cannot
be specified, so if the IC is to be used in applications
where parameters may exceed the absolute maximum
ratings, then be sure to incorporate fuses, or other physi-
cal safety measures.
(2) GND potential
The potential for pin 1 must be kept lower than the poten-
sials ofthe other pins regardless of the circumstances.
(3) Input pins
Voltage should never be applied to the input pins when
the VCC voltage is not applied to the IC. Similarly, when
VCC is applied, the voltage on each input pin should be
less than VCC and within the guaranteed range for the
electrical characteristics.
(4) Back-rush voltage
Depending on the ambient conditions, environment, or
motor characteristics, the back-rush voltage may fluctu-
ate. Be sure to confirm that the back-rush voltage will not
adversely affect the operation of the IC.
(5) Large current line
Large currents are carried by the motor power supply and
motor ground for these ICs.
Therefore, the layout of the pattern of the PC board and
the constants of certain parameters for external compo-
nents, such as the capacitor between the power supply
and ground, may cause this large output current to flow
back to the input pins, resulting in output oscillation or
other malfunctions. To prevent this, make sure that the
PC board layout and external circuit constants cause no
problems with the characteristics of these ICs.
(6) Power dissipation
The power dissipation will fluctuate depending on the
mounting conditions of the IC and the ambient environ-
ment. Make sure to carefully check the thermal design of
the application where these ICs will be used.
(7) Power consumption
The power consumption by the IC varies widely with the
power supply voltage and the output current. Give full
consideration to the power dissipation rating and the
thermal resistance data and transient thermal resistance
data, to provide a thermal design so that none of the rat-
ings for the IC are exceeded.
(8) Current consumption
The ratio of current consumption (ICC1 versus ICC2) is 1 :
2 for the logic section GND (pins 2 and 5) and the power
section GND (pin 8).
464










Скачать PDF:

[ BA6418N.PDF Даташит ]

Номер в каталогеОписаниеПроизводители
BA6418NReversible motor driverROHM Semiconductor
ROHM Semiconductor

Номер в каталоге Описание Производители
TL431

100 мА, регулируемый прецизионный шунтирующий регулятор

Unisonic Technologies
Unisonic Technologies
IRF840

8 А, 500 В, N-канальный МОП-транзистор

Vishay
Vishay
LM317

Линейный стабилизатор напряжения, 1,5 А

STMicroelectronics
STMicroelectronics

DataSheet26.com    |    2020    |

  Контакты    |    Поиск