|
|
PDF 74ALVT162731 Data sheet ( Hoja de datos )
| Número de pieza | 74ALVT162731 | |
| Descripción | 2.5V/3.3V 1-to-4 address register/driver with 30ohm termination resistors 3-State | |
| Fabricantes | NXP Semiconductors | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de 74ALVT162731 (archivo pdf) en la parte inferior de esta página. Total 12 Páginas | ||
|
No Preview Available !
INTEGRATED CIRCUITS
74ALVT162731
2.5V/3.3V 1-to-4 address register/driver
with 30Ω termination resistors (3-State)
Product specification
IC24 Data Handbook
1999 Mar 23
Philips
Semiconductors
1 page  
Philips Semiconductors
2.5V/3.3V 1-to-4 address register/driver with 30Ω
termination resistors (3-State)
Product specification
74ALVT162731
DC ELECTRICAL CHARACTERISTICS (3.3V "0.3V RANGE)
LIMITS
SYMBOL
PARAMETER
TEST CONDITIONS
Temp = -40°C to +85°C UNIT
MIN TYP1 MAX
VIK Input clamp voltage
VOH High-level output voltage
VCC = 3.0V; IIK = –18mA
VCC = 3.0V; IOH = –12mA
–0.85 –1.2
2.0 2.5
V
V
VOL Low–level output voltage
VCC = 3.0V; IOL = 12mA
0.5 0.8
V
VRST
II
IOFF
IHOLD
IEX
IPU/PD
Power-up output low voltage6
Input leakage current
Off current
Bus Hold current
Data inputs7
Current into an output in the
High state when VO > VCC
Power up/down 3-State output
current3
VCC = 3.6V; IO = 1mA; VI = VCC or GND
VCC = 3.6V; VI = VCC or GND
VCC = 0 or 3.6V; VI = 5.5V
VCC = 3.6V; VI = VCC
VCC = 3.6V; VI = 0
VCC = 0V; VI or VO = 0 to 4.5V
VCC = 3V; VI = 0.8V
VCC = 3V; VI = 2.0V
VCC = 0V to 3.6V; VCC = 3.6V
Control pins
Data pins4
VO = 5.5V; VCC = 3.0V
VCC ≤ 1.2V; VO = 0.5V to VCC; VI = GND or VCC
OE/OE = Don’t care
75
–75
±500
0.1
0.1
0.5
0.1
0.1
130
–140
0.55
±1
10
1
-5
±100
10 125
1 ±100
V
µA
µA
µA
µA
µA
IOZH 3-State output High current
VCC = 3.6V; VO = 3.0V; VI = VIL or VIH
0.5 5 µA
IOZL 3-State output Low current
VCC = 3.6V; VO = 0.5V; VI = VIL or VIH
0.5 –5 µA
ICCH
VCC = 3.6V; Outputs High, VI = GND or VCC, IO = 0
0.05 0.1
ICCL
ICCZ
Quiescent supply current
VCC = 3.6V; Outputs Low, VI = GND or VCC, IO = 0
VCC = 3.6V; Outputs Disabled; VI = GND or VCC, IO=05
7.0 9.0
0.06 0.1
mA
∆ICC
Additional supply current per
input pin2
VCC = 3V to 3.6V; One input at VCC–0.6V,
Other inputs at VCC or GND
0.04 0.4 mA
NOTES:
1. All typical values are at VCC = 3.3V and Tamb = 25°C.
2. This is the increase in supply current for each input at the specified voltage level other than VCC or GND
3. This parameter is valid for any VCC between 0V and 1.2V with a transition time of up to 10msec. From VCC = 1.2V to VCC = 3.3V ± 0.3V a
transition time of 100µsec is permitted. This parameter is valid for Tamb = 25°C only.
4. Unused pins at VCC or GND.
5. ICCZ is measured with outputs pulled up to VCC or pulled down to ground.
6. For valid test results, data must not be loaded into the flip-flops (or latches) after applying power.
7. This is the bus hold overdrive current required to force the input to the opposite logic state.
1999 Mar 23
5
5 Page 
Philips Semiconductors
2.5 V/3.3 V 1-to-4 address register/driver with 30Ω
termination resistors (3-State)
Product specification
74ALVT162731
TSSOP56: plastic thin shrink small outline package; 56 leads; body width 6.1mm
SOT364-1
1999 Mar 30
11
11 Page | ||
| Páginas | Total 12 Páginas | |
| PDF Descargar | [ Datasheet 74ALVT162731.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| 74ALVT162731 | 2.5V/3.3V 1-to-4 address register/driver with 30ohm termination resistors 3-State | NXP Semiconductors |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |