|
|
Número de pieza | SAA7185BWP | |
Descripción | Digital Video Encoders DENC2-M6 | |
Fabricantes | NXP Semiconductors | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de SAA7185BWP (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
No Preview Available ! INTEGRATED CIRCUITS
DATA SHEET
SAA7184; SAA7185B
Digital Video Encoders
(DENC2-M6)
Preliminary specification
Supersedes data of 1995 Nov 14
File under Integrated Circuits, IC22
1996 Jul 03
1 page Philips Semiconductors
Digital Video Encoders (DENC2-M6)
Preliminary specification
SAA7184; SAA7185B
SYMBOL
CHROMA
VDDA2
Y
VSSA
CVBS
VDDA3
IOA
VDDA4
RES
DTACK
RWN/SCL
A0/SDA
CSN/SA
VSSD7
DP0 to DP3
VDDD3
SEL_MPU
PIN
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63 to 66
67
68
I/O DESCRIPTION
O analog output of the chrominance signal
I analog supply voltage 2 for the DACs and output amplifiers
O analog output of the luminance signal
− analog ground for the DACs and output amplifiers
O analog output of the CVBS signal
I analog supply voltage 3 for the DACs and output amplifiers
I current input for the output amplifiers (connected via a 15 kΩ resistor to
VDDA)
I analog supply voltage 4 for the DACs and output amplifiers
I Reset input, active LOW. After reset is applied, all outputs are in 3-state input
mode. The I2C-bus receiver waits for the start condition.
O Data acknowledge output of the parallel MPU interface, active LOW,
otherwise high impedance.
I If pin 68 (SEL_MPU) is HIGH, this is the read/write signal of the parallel MPU
interface. Otherwise it is the I2C-bus serial clock input.
I/O If pin 68 (SEL_MPU) is HIGH, this is the address signal of the parallel MPU
interface. Otherwise it is the I2C-bus serial data input/output.
I If pin 68 (SEL_MPU) is HIGH, this is the chip select signal of the parallel
MPU interface. Otherwise it is the I2C-bus slave address select pin. When
LOW slave address = 88H, when HIGH slave address = 8CH.
− digital ground 7
I/O Lower 4 bits of the data port; if pin 68 (SEL_MPU) is HIGH, the data bus of
the parallel MPU interface is used. If pin 68 is LOW, then the UV lines of the
video port are used.
I digital supply voltage 3
I Select MPU interface input; if it is HIGH, the parallel MPU interface is active,
if not the I2C-bus interface will be used.
1996 Jul 03
5
5 Page Philips Semiconductors
Digital Video Encoders (DENC2-M6)
Preliminary specification
SAA7184; SAA7185B
1996 Jul 03
11
11 Page |
Páginas | Total 30 Páginas | |
PDF Descargar | [ Datasheet SAA7185BWP.PDF ] |
Número de pieza | Descripción | Fabricantes |
SAA7185BWP | Digital Video Encoders DENC2-M6 | NXP Semiconductors |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |