DataSheet26.com

Z86C95 PDF даташит

Спецификация Z86C95 изготовлена ​​​​«Zilog.» и имеет функцию, называемую «CMOS Z8 DIGITAL SIGNAL PROCESSOR (DSP)».

Детали детали

Номер произв Z86C95
Описание CMOS Z8 DIGITAL SIGNAL PROCESSOR (DSP)
Производители Zilog.
логотип Zilog. логотип 

18 Pages
scroll

No Preview Available !

Z86C95 Даташит, Описание, Даташиты
Z86C95 DSP
CPS DC-4067-13
CUSTOMER PROCUREMENT SPECIFICATION
GENERAL DESCRIPTION
The Z86C95 MCU (Microcontroller Unit ) introduces a new
level of sophistication to Superintegration™ ICs. The
Z86C95 is a member of the Z8® single-chip microcontroller
family incorporating a CMOS ROMless Z8 microcontroller
with an embedded DSP processor for digital servo control.
The DSP slave processor can perform 16-bit x 16-bit
multiplicates and accumulates in one clock cycle. Addi-
tionally, the Z86C95 is further enhanced with a hardwired
16-bitx16-bit multiplier and a 32-bit/16-bit divider, three
16-bit counter timers with capture and compare registers,
a half flash 8-channel 8-bit A/D converter with a 2 µsec
conversion time, an 8-bit DAC with 1/4 programmable gain
stage, UART, serial peripheral interface, and a PWM
output channel (Functional Block Diagram). It is fabricated
using CMOS technology and offered in an 80-pin QFP, 84-
pin PLCC, or 100-pin VQFP package.
The Z86C95 provides up to 16 output address lines thus
permitting an address space of up to 64 Kbytes of data and
program memory each. Eight address outputs (AD7-AD0)
are provided by a multiplexed, 8-bit, Address/Data bus.
The remaining 8 bits are provided via output address bits
A15-A8.
Z86C95
CMOS Z8® DIGITAL
SIGNAL PROCESSOR (DSP)
There are 256 registers located on chip and organized as
236 general-purpose registers, 16 control and status reg-
isters, and four I/O port registers. The register file can be
divided into sixteen groups of 16 working registers each.
Configuration of the registers in this manner allows the use
of short format instructions; in addition, any of the indi-
vidual registers can be accessed directly. Also, the Z86C95
contains 512 bytes of DSP Program RAM and 128 words
of DSP data RAM.
Notes:
All Signals with a preceding front slash, "/", are active Low, e.g.:
B//W (WORD is active Low); /B/W (BYTE is active Low, only).
Power connections follow conventional descriptions below:
Connection
Circuit
Device
Power
Ground
V
CC
GND
V
DD
V
SS
OPERATING ERRATA
This notice only applies to devices top marked "Z86C9524
ASC/FSC/VSC" with a date code of 9237 or later.
The following operating errata only applies to devices
topmarked with "Z86C95 ASC/FSC/VSC."
1. A DSP load to the DAC Register fails below approxi-
mately VCC = 4.7V.
2. Clipping occurs in the linearity of the DAC with a 100K
load at about 3.3V output (VDHI = 3.5V).
3. ICC1 at HALT Mode will show a current of 17-18 mA,
then will jump to 40-70 mA, and will settle between 17-
24 mA. Settling time is about 10-15 seconds.
4. ICC2 at STOP Mode and DSP Pause will show a current
of 1-2 mA, then will jump to 5-7 mA, and will settle at 3-
4 mA. Settling time is about 10-15 seconds.
1. ICC1 at HALT Mode will show a current of 17-18 mA,
then will jump to 40-70 mA, and will settle between 17-
24 mA. Settling time is about 10-15 seconds.
2. ICC2 at STOP Mode and DSP Pause will show a
current of 1-2 mA, then will jump to 5-7 mA, and will
settle at 3-4 mA. Settling time is about 10-15 seconds.
The following operating errata only applies to devices
topmarked with "Z86C9540 ASC/FSC/VSC or SL 1636."
1. ICC1 at HALT Mode will show a current of 17-18 mA,
then will jump to 40-70 mA, and will settle between 17-
24 mA. Settling time is about 10-15 seconds.
DC-4067-13 (5-17-94)
1









No Preview Available !

Z86C95 Даташит, Описание, Даташиты
Z86C95 DSP
CPS DC-4067-13
GENERAL DESCRIPTION (Continued)
2. ICC2 at STOP Mode and DSP Pause will show a
current of 1-2 mA, then will jump to 5-7 mA, and will
settle at 3-4 mA. Settling time is about 10-15 seconds.
3. The zero error for the ADC at 25°C is about 180 mV.
Output Input
Vcc GND
XTAL /AS /DS R//W /RESET /WAIT
Port 3
SPI
UART
Three 16-Bit
Counter/
Timers
32 ÷ 16
Divider
16 x 16
Multiplier
Interrupt
Control
ALU
Flags
Register
Pointer
Register File
256 x 8-Bit
Machine Timing and
Instruction Control
Program
Counter
Digital Signal Processor
DSP RAM
Bank 1
DSP RAM
Bank 2
Program
RAM
Port 2
I/O
(Bit Programmable)
Address
A15-A0*
* In multiplexed mode,
A7-A0 reflects the DSP
address bus for emulation.
AD7-AD0
8
Address/Data
ADC
8 Channel
Analog In
DAC
Analog
Out
PWM
PWM
Functional Block Diagram
2









No Preview Available !

Z86C95 Даташит, Описание, Даташиты
PIN DESCRIPTION
P2(0)
P2(1)
P2(2)
P2(3)
P2(4)
P2(5)
P2(6)
P2(7)
VSS
ANGND
AVCC
VAHI
VALO
ANA(0)
ANA(1)
ANA(2)
64
65
80
1
Z86C95
80-Lead QFP
80-Lead QFP Pin Assignments
Z86C95 DSP
CPS DC-4067-13
41
40 A3
A2
A1
A0
AD0
VSS
AD1
AD2
AD3
AD4
AD5
AD6
AD7
R/W
/DS
25 /AS
24
3










Скачать PDF:

[ Z86C95.PDF Даташит ]

Номер в каталогеОписаниеПроизводители
Z86C90ROMLESS CMOS Z8 8-BIT MICROCONTROLLERZilog.
Zilog.
Z86C90PLCCROMLESS CMOS Z8 8-BIT MICROCONTROLLERZilog.
Zilog.
Z86C90QFPROMLESS CMOS Z8 8-BIT MICROCONTROLLERZilog.
Zilog.
Z86C9116CMOS Z8 ROMless MicrocontrollersZilog
Zilog

Номер в каталоге Описание Производители
TL431

100 мА, регулируемый прецизионный шунтирующий регулятор

Unisonic Technologies
Unisonic Technologies
IRF840

8 А, 500 В, N-канальный МОП-транзистор

Vishay
Vishay
LM317

Линейный стабилизатор напряжения, 1,5 А

STMicroelectronics
STMicroelectronics

DataSheet26.com    |    2020    |

  Контакты    |    Поиск