|
|
PDF N74F322N Data sheet ( Hoja de datos )
| Número de pieza | N74F322N | |
| Descripción | 8-bit serial/parallel register with sign extend 3-State | |
| Fabricantes | Philips | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de N74F322N (archivo pdf) en la parte inferior de esta página. Total 9 Páginas | ||
|
No Preview Available !
Philips Semiconductors
8-bit serial/parallel register with sign extend (3-State)
Product specification
74F322
FEATURES
• Multiplexed parallel I/O ports
• Separate serial input and output
• Sign extend function
• 3-State outputs for bus applications
• Direct Overriding Clear
DESCRIPTION
The 74F322 is an 8-bit shift register with provision for either serial or
parallel loading and with 3-State parallel outputs plus a bi-state
serial output. Parallel data inputs and outputs are multiplexed to
minimize pin count. State changes are initiated by the rising edge of
the clock. Four synchronous modes of operation are possible: hold
(store), shift right with serial entry, shift right with sign extend, and
parallel load. An asynchronous Master Reset (MR) input overrides
clocked operation and clears the registers.
The 74F322 contains eight D-type edge triggered flip-flops and the
interstage gating required to perform right shift and the intrastage
gating necessary for hold and synchronous parallel load operations.
A Low signal on RE enables shifting or parallel loading, while a High
signal enables the hold mode. A High signal on S/P enables shift
right, while a Low signal disables the 3-State output buffers and
enables parallel loading. In the shift right mode a High signal on SE
enables serial entry from either D0 or D1, as determined by the S
input. A Low signal on SE enables shift right, but Q7 reloads its
contents, thus performing the sign extend function. A High signal on
OE disables the 3-State output buffers, regardless of the other
control inputs. In this condition the shifting and loading operations
can still be performed.
PIN CONFIGURATION
RE 1
S/P 2
D0 3
I/O0 4
I/O2 5
I/O4 6
I/O6 7
OE 8
MR 9
GND 10
20 VCC
19 S
18 SE
17 D1
16 I/O1
15 I/O3
14 I/O5
13 I/O7
12 Q7
11 CP
SF00874
TYPE
74F322
TYPICAL fMAX
125MHz
TYPICAL
SUPPLY CURRENT
(TOTAL)
60mA
ORDERING INFORMATION
DESCRIPTION
20-pin plastic DIP
ORDER CODE
COMMERCIAL RANGE
VCC = 5V ±10%, Tamb = 0°C to +70°C
N74F322N
20-pin plastic SOL
N74F322D
INPUT AND OUTPUT LOADING AND FAN-OUT TABLE
PINS
DESCRIPTION
74F(U.L.)
HIGH/LOW
D0, D1
Serial data inputs
1.0/1.0
S Serial data select input
1.0/2.0
SE Sign Extend input
1.0/3.0
CP Clock Pulse input (Active rising edge)
1.0/1.0
S/P Serial (High) or Parallel (Low) mode control input
1.0/1.0
RE Register Enable input (Active Low)
1.0/1.0
MR Asynchronous Master Reset input (Active Low)
1.0/1.0
OE Output Enable input (Active Low)
1.0/1.0
Q7 Bi-state serial output
50/33
Multiplexed parallel data inputs or
I/On
3-State parallel outputs
NOTE: One (1.0) FAST Unit Load (U.L.) is defined as: 20µA in the High State and 0.6mA in the Low state.
3.5/1.0
150/40
LOAD VALUE
HIGH/LOW
20µA/0.6mA
20µA/1.2mA
20µA/1.8mA
20µA/0.6mA
20µA/0.6mA
20µA/0.6mA
20µA/0.6mA
20µA/0.6mA
1.0mA/20mA
70µA/0.6mA
3.0mA/24mA
1988 Apr 22
1 853-0366 93020
1 page  
Philips Semiconductors
8-bit serial/parallel register with sign extend (3-State)
Product specification
74F322
DC ELECTRICAL CHARACTERISTICS
(Over recommended operating free-air temperature range unless otherwise noted.)
SYMBOL
PARAMETER
TEST CONDITIONS1
LIMITS
MIN TYP2 MAX
UNIT
VOH
High-level output voltage
Q7
I/On
VCC = MIN,
VIL = MAX,
VIH = MIN
IOH = –1mA
IOH = –3mA
±10%VCC
±5%VCC
±10%VCC
2.5
2.7
2.4
3.4
±5%VCC
2.7
3.3
V
V
V
V
VOL Low-level output voltage
VCC = MIN,
VIL = MAX,
VIH = MIN
IOL = MAX
±10%VCC
±5%VCC
0.38 0.55
0.35 0.50
V
V
VIK Input clamp voltage
VCC = MIN, II = IIK
–0.73 –1.2
V
II Input current at
others
maximum input voltage
I/On
VCC = MAX, VI = 7.0V
VCC = MAX, VI = 5.5V
100 µA
1 mA
IIH High-level input current
VCC = MAX, VI = 2.7V
20 µA
SE –1.8 mA
IIL
Low-level input current
S
others
VCC = MAX, VI = 0.5V
–1.2 mA
–0.6 mA
IIH + IOZH
Off-state output current
High-level voltage applied
VCC = MAX, VI = 2.7V
70 µA
IIL + IOZL
Off-state output current
Low-level voltage applied
VCC = MAX, VI = 0.5V
–0.6 mA
IOS Short-circuit output current3
VCC = MAX
–60
–150
mA
ICCH
50 75
mA
ICC
Supply current (total)
ICCL
VCC = MAX
60 90
mA
ICCZ
65 95
mA
NOTES:
1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type.
2. All typical values are at VCC = 5V, Tamb = 25°C.
3. Not more than one output should be shorted at a time. For testing IOS, the use of high-speed test apparatus and/or sample-and-hold
techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting
of a High output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any
sequence of parameter tests, IOS tests should be performed last.
1988 Apr 22
5
5 Page | ||
| Páginas | Total 9 Páginas | |
| PDF Descargar | [ Datasheet N74F322N.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| N74F322D | 8-bit serial/parallel register with sign extend 3-State | Philips |
| N74F322N | 8-bit serial/parallel register with sign extend 3-State | Philips |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |