DataSheet26.com

NCP1377 PDF даташит

Спецификация NCP1377 изготовлена ​​​​«ON» и имеет функцию, называемую «PWM Current-Mode Controller for Free-Running Quasi-Resonant Operation».

Детали детали

Номер произв NCP1377
Описание PWM Current-Mode Controller for Free-Running Quasi-Resonant Operation
Производители ON
логотип ON логотип 

17 Pages
scroll

No Preview Available !

NCP1377 Даташит, Описание, Даташиты
NCP1377, NCP1377B
PWM Current-Mode
Controller for Free-Running
Quasi-Resonant Operation
The NCP1377 combines a true current mode modulator and a
demagnetization detector which ensures full borderline/critical
Conduction Mode in any load/line conditions together with
minimum drain voltage switching (QuasiResonant operation). Due
to its inherent skip cycle capability, the controller enters burst mode
as soon as the power demand falls below a predetermined level. As
this happens at low peak current, no audible noise can be heard. For
NCP1377, an internal 8.0 ms timer prevents the freerun frequency to
exceed 100 kHz (therefore below the 150 kHz CISPR22 EMI
starting limit), while the skip adjustment capability lets the user
select the frequency at which the burst foldback takes place. For
NC1377B, the internal timer duration is reduced to 3.0 ms to allow
operation at higher frequencies (up to 300 kHz).
The transformer core reset detection is done through an auxiliary
winding which, brought via a dedicated pin, also enables fast
Over Voltage Protection (OVP). Once an OVP has been detected, the
IC permanently latches off. The 1377 features a sampling time of
4.5 ms whereas it is 1.5 ms for the B version.
The NCP1377 also features an efficient protective circuitries
which, in presence of an overcurrent condition, disables the output
pulses and enters a safe burst mode, trying to restart. Once the default
has gone, the device autorecovers. Finally an internal 1.0 ms
SoftStart eliminates the traditional startup stress.
Features
FreeRunning Borderline/Critical Mode QuasiResonant Operation
Latched Overvoltage Protection
AutoRecovery ShortCircuit Protection Via UVLO Crossover
External Latch Triggering, e.g. Via Overtemperature Signal
CurrentMode with Adjustable Skip Cycle Capability
Internal 1.0 ms SoftStart
Internal Temperature Shutdown
Internal Leading Edge Blanking
500 mA Peak Current Source/Sink Capability
Under Voltage Lockout Level of 12.5 V (On) and 7.5 V (Min)
Direct Optocoupler Connection
SPICE Models Available for TRANsient Analysis
Internal Minimum TOFF
These Devices are PbFree, Halogen Free/BFR Free and are RoHS
Compliant
Typical Applications
ACDC Adapters for Notebooks, etc.
Offline Battery Chargers
Consumer Electronics (DVD Players, SetTop Boxes, TVs, etc.)
Auxiliary Power Supplies (USB, Appliances, TVs, etc.)
http://onsemi.com
8
1
SOIC8
DR SUFFIX
CASE 751
MARKING DIAGRAMS
8
1377
ALYW
G
1
8
1377B
ALYW
G
1
8
1
SOIC7
D1 SUFFIX
CASE 751U
8
377D1
ALYW G
G
1
8
1
PDIP7
P SUFFIX
CASE 626B
1
1377P
AWL
YYWWG
1
1377BP
AWL
YYWWG
A = Assembly Location
L, WL = Wafer Lot
Y, YY = Year
W, WW = Work Week
G or G = PbFree Package
(Note: Microdot may be in either location)
PIN CONNECTIONS
Dmg 1
FB 2
CS 3
GND 4
8 HV
6 VCC
5 Drv
(Top View)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 14 of this data sheet.
© Semiconductor Components Industries, LLC, 2011
January, 2011 Rev. 11
1
Publication Order Number:
NCP1377/D









No Preview Available !

NCP1377 Даташит, Описание, Даташиты
Universal
Network
NCP1377, NCP1377B
R*
+
OVP and
Demag
NCP1377
18
27
36
45
12 V @ 1 A
+
GND
+
*Please refer to the application information section.
Y1 Type
Figure 1. Typical Application Schematic
PIN FUNCTION DESCRIPTION
Pin Symbol
Function
1 Demag Core reset detection and OVP
2 FB Sets the peak current setpoint
3 CS Current sense input and skip
cycle level selection
4 GND
5 Drv
6 VCC
7 NC
8 HV
The IC ground
Driving pulses
Supplies the IC
Highvoltage pin
Description
The auxiliary FLYBACK signal ensures discontinuous operation and offers a fixed
overvoltage detection level of 7.2 V.
By connecting an optocoupler to this pin, the peak current setpoint is adjusted
accordingly to the output power demand. By bringing this pin below the internal
skip level, you shut off the device.
This pin senses the primary current and routes it to the internal comparator via an
L.E.B. By inserting a resistor in series with the pin, you control the level at which
the skip operation takes place.
The driver’s output to an external MOSFET.
This pin is connected to an external bulk capacitor of typically 10 mF.
This unconnected pin ensures adequate creepage distance.
Connected to the highvoltage rail, this pin injects a constant current into the VCC
bulk capacitor and ensures a clean lossless startup sequence.
http://onsemi.com
2









No Preview Available !

NCP1377 Даташит, Описание, Даташиты
NCP1377, NCP1377B
4.5 us 1.5 us for B Version
Delay
HV
4 mA
VCC
PON
+
+
12.5 V
7.5 V
5.6 V (Fault)
OVP
Demag
5 V /1.44
+
+
8 us
Blanking
SQ
3 us for
B Version
SQ
RR
+
Demag
+
50 mV
10 V
Rint
VCC
Drv
Driver src = 20 sink = 10
4.2 V
To Internal
Supply
GND
Fault
Mngt.
+
-
Overload?
5 us
Timeout
Time
Reset
/3
1V
200 mA
when DRV
is OFF
380 ns
LEB
Demag
FB
CS
Figure 2. Internal Circuit Architecture
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
Continuous Power Supply or Drive Voltage
Transient Power Supply Voltage, Duration < 10 ms, IVCC < 20 mA
Maximum Voltage on all other pins except Pin 8 (HV), Pin 6 (VCC) and Pin 5 (Drv)
Maximum Current into all pins except VCC (6), HV (8) and Demag (1) when 10 V ESD di-
odes are activated
VCC, Drv
VCC Pulse
18
25
0.3 to 10
5.0
V
V
V
mA
Maximum Current in Pin 1
Idem
+3.0/2.0
mA
Thermal Resistance, JunctiontoCase
Thermal Resistance, JunctiontoAir, SOIC Version
Thermal Resistance, JunctiontoAir, PDIP Version
Maximum Junction Temperature
Temperature Shutdown
RqJC
RqJA
RqJA
TJMAX
57 °C/W
178 °C/W
100 °C/W
150 °C
155 °C
Hysteresis in Shutdown
Storage Temperature Range
30 °C
60 to +150
°C
ESD Capability, HBM Model (All pins except VCC and HV)
ESD Capability, Machine Model
2.0 kV
200 V
Maximum Voltage on Pin 8 (HV), Pin 6 (VCC) Decoupled to Ground with 10 mF
VHV 500 V
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
http://onsemi.com
3










Скачать PDF:

[ NCP1377.PDF Даташит ]

Номер в каталогеОписаниеПроизводители
NCP1377PWM Current-Mode Controller for Free-Running Quasi-Resonant OperationON
ON
NCP1377BPWM Current-Mode Controller for Free-Running Quasi-Resonant OperationON Semiconductor
ON Semiconductor
NCP1378PWM Current-Mode ControllerON Semiconductor
ON Semiconductor
NCP1379Quasi-Resonant Current-Mode ControllerON Semiconductor
ON Semiconductor

Номер в каталоге Описание Производители
TL431

100 мА, регулируемый прецизионный шунтирующий регулятор

Unisonic Technologies
Unisonic Technologies
IRF840

8 А, 500 В, N-канальный МОП-транзистор

Vishay
Vishay
LM317

Линейный стабилизатор напряжения, 1,5 А

STMicroelectronics
STMicroelectronics

DataSheet26.com    |    2020    |

  Контакты    |    Поиск