|
|
PDF OPA621 Data sheet ( Hoja de datos )
| Número de pieza | OPA621 | |
| Descripción | Wideband Precision OPERATIONAL AMPLIFIER | |
| Fabricantes | Burr-Brown | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de OPA621 (archivo pdf) en la parte inferior de esta página. Total 16 Páginas | ||
|
No Preview Available !
® OPA621
Wideband Precision
OPERATIONAL AMPLIFIER
FEATURES
q LOW NOISE: 2.3nV/√Hz
q LOW DIFFERENTIAL GAIN/PHASE ERROR
q HIGH OUTPUT CURRENT: 150mA
q FAST SETTLING: 25ns (0.01%)
q GAIN-BANDWIDTH: 500MHz
q STABLE IN GAINS: ≥ 2V/V
q LOW OFFSET VOLTAGE: ±100µV
q SLEW RATE: 500V/µs
q 8-PIN DIP, SOIC PACKAGES
DESCRIPTION
The OPA621 is a precision wideband monolithic opera-
tional amplifier featuring very fast settling time, low
differential gain and phase error, and high output
current drive capability.
The OPA621 is stable in gains of ±2V/V or higher. This
amplifier has a very low offset, fully symmetrical
differential input due to its “classical” operational am-
plifier circuit architecture. Unlike “current-feedback”
APPLICATIONS
q LOW NOISE PREAMPLIFIER
q LOW NOISE DIFFERENTIAL AMPLIFIER
q HIGH-RESOLUTION VIDEO
q LINE DRIVER
q HIGH-SPEED SIGNAL PROCESSING
q ADC/DAC BUFFER
q ULTRASOUND
q PULSE/RF AMPLIFIERS
q ACTIVE FILTERS
amplifier designs, the OPA621 may be used in all op
amp applications requiring high speed and precision.
Low noise and distortion, wide bandwidth, and high
linearity make this amplifier suitable for RF and video
applications. Short circuit protection is provided by an
internal current-limiting circuit.
The OPA621 is available in DIP and SO-8 packages.
+VCC
7
Non-Inverting 3
Input
Inverting
Input
2
Current
Mirror
Output
Stage
6 Output
4
–VCC
International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 • Twx: 910-952-1111
Internet: http://www.burr-brown.com/ • FAXLine: (800) 548-6133 (US/Canada Only) • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132
©1989 Burr-Brown Corporation
PDS-939F
Printed in U.S.A. June, 1997
1 page  
TYPICAL PERFORMANCE CURVES
At VCC = ±5VDC, RL = 100Ω, and TA = +25°C, unless otherwise noted.
OPEN-LOOP FREQUENCY RESPONSE
80
60
40
20
0
–20
1k
0
–45
Gain
Phase
–90
–135
Phase
Margin
≈ 50°
–180
10k 100k 1M
10M 100M 1G
Frequency (Hz)
+10
+8
+6
+4
+2
0
–2
1M
A V = +2V/V CLOSED-LOOP
SMALL-SIGNAL BANDWIDTH
Gain
AOL
f –3dB ≈ 500MHz
Open-Loop Phase
0
–45
–90
PM ≈ 50°
10M 100M
Frequency (Hz)
–135
–180
1G
+18
+16
+14
+12
+10
+8
+6
1M
A V = +5V/V CLOSED-LOOP
SMALL-SIGNAL BANDWIDTH
Gain
f –3dB ≈ 100MHz
Open-Loop Phase
AOL
PM ≈ 70°
10M
100M
Frequency (Hz)
0
–45
–90
–135
–180
1G
A V = +10V/V CLOSED-LOOP
SMALL-SIGNAL BANDWIDTH
+24
+22
Gain
AOL
+20
+18 f –3dB ≈ 50MHz
+16
Open-Loop Phase
+14
PM ≈ 80°
+12
1M
10M
100M
Frequency (Hz)
0
–45
–90
–135
–180
1G
A V = +2V/V CLOSED-LOOP BANDWIDTH
vs OUTPUT VOLTAGE SWING
8
RL = 50Ω
6
4
2
0
1k
10k 100k 1M
10M 100M 1G
Frequency (Hz)
A V = +5V/V CLOSED-LOOP BANDWIDTH
vs OUTPUT VOLTAGE SWING
8
RL = 50Ω
6
4
2
0
1k
10k 100k 1M
10M 100M 1G
Frequency (Hz)
®
5 OPA621
5 Page 
recommended. Circuits using all surface mount components
with the OPA621AU (SO-8 package) will offer the best AC
performance. The parasitic package inductance and capaci-
tance for the SO-8 is lower than the both the Cerdip and
8-lead Plastic DIP.
6) Avoid overloading the output. Remember that output
current must be provided by the amplifier to drive its own
feedback network as well as to drive its load. Lowest
distortion is achieved with high impedance loads.
7) Don’t forget that these amplifiers use ±5V supplies.
Although they will operate perfectly well with +5V and
–5.2V, use of ±15V supplies will destroy the part.
8) Standard commercial test equipment has not been
designed to test devices in the OPA621’s speed range.
Benchtop op amp testers and ATE systems will require a
special test head to successfully test these amplifiers.
9) Terminate transmission line loads. Unterminated lines,
such as coaxial cable, can appear to the amplifier to be a
capacitive or inductive load. By terminating a transmission
line with its characteristic impedance, the amplifier’s load
then appears purely resistive.
10) Plug-in prototype boards and wire-wrap boards will not
be satisfactory. A clean layout using RF techniques is
essential; there are no shortcuts.
OFFSET VOLTAGE ADJUSTMENT
The OPA621’s input offset voltage is laser-trimmed and will
require no further adjustment for most applications. How-
ever, if additional adjustment is needed, the circuit in Figure
1 can be used without degrading offset drift with tempera-
ture. Avoid external adjustment whenever possible since
extraneous noise, such as power supply noise, can be
inadvertently coupled into the amplifier’s inverting input
terminal. Remember that additional offset errors can be
created by the amplifier’s input bias currents. Whenever
possible, match the impedance seen by both inputs as is
shown with R3. This will reduce input bias current errors to
the amplifier’s offset current, which is typically only 0.2µA.
INPUT PROTECTION
Static damage has been well recognized for MOSFET
devices, but any semiconductor device deserves protection
from this potentially damaging source. The OPA621 incor-
porates on-chip ESD protection diodes as shown in Figure 2.
This eliminates the need for the user to add external
protection diodes, which can add capacitance and degrade
AC performance.
External
Pin
+VCC
ESD Protection diodes internally
connected to all pins.
Internal
Circuitry
–VCC
FIGURE 2. Internal ESD Protection.
All pins on the OPA621 are internally protected from ESD
by means of a pair of back-to-back reverse-biased diodes to
either power supply as shown. These diodes will begin to
conduct when the input voltage exceeds either power supply
by about 0.7V. This situation can occur with loss of the
amplifier’s power supplies while a signal source is still
present. The diodes can typically withstand a continuous
current of 30mA without destruction. To insure long term
reliability, however, diode current should be externally
limited to 10mA or so whenever possible.
The internal protection diodes are designed to withstand
2.5kV (using Human Body Model) and will provide
adequate ESD protection for most normal handling proce-
dures. However, static damage can cause subtle changes in
amplifier input characteristics without necessarily destroy-
ing the device. In precision operational amplifiers, this may
cause a noticeable degradation of offset voltage and drift.
Therefore, static protection is strongly recommended when
handling the OPA621.
+VCC
20kΩ
RTrim
47kΩ
–VCC
R1
R2
OPA621
*R3 = R1 || R2
VIN or Ground
Output Trim Range ≅ +V CC ( R2 ) to –VCC ( R2 )
RTrim
RTrim
* R is optional and can be used to cancel offset errors due to input bias
3
currents.
FIGURE 1. Offset Voltage Trim.
OUTPUT DRIVE CAPABILITY
The OPA621’s design uses large output devices and has
been optimized to drive 50Ω and 75Ω resistive loads. The
device can easily drive 6Vp-p into a 50Ω load. This high-
output drive capability makes the OPA621 an ideal choice
for a wide range of RF, IF, and video applications. In many
cases, additional buffer amplifiers are unneeded.
Internal current-limiting circuitry limits output current to
about 150mA at 25°C. This prevents destruction from
accidental shorts to common and eliminates the need for
external current-limiting circuitry. Although the device can
withstand momentary shorts to either power supply, it is not
recommended.
Many demanding high-speed applications such as ADC/
DAC buffers require op amps with low wideband output
impedance. For example, low output impedance is essential
®
11 OPA621
11 Page | ||
| Páginas | Total 16 Páginas | |
| PDF Descargar | [ Datasheet OPA621.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| OPA620 | Wideband Precision Operational Amplifier |  Texas Instruments |
| OPA620 | Wideband Precision OPERATIONAL AMPLIFIER | Burr-Brown |
| OPA621 | Wideband Precision Operational Amplifier | Texas Instruments |
| OPA621 | Wideband Precision OPERATIONAL AMPLIFIER | Burr-Brown |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |