DataSheet26.com

OZ998 PDF даташит

Спецификация OZ998 изготовлена ​​​​«ETC» и имеет функцию, называемую «Intelligent Manager Smart Multi-DIMM Selector».

Детали детали

Номер произв OZ998
Описание Intelligent Manager Smart Multi-DIMM Selector
Производители ETC
логотип ETC логотип 

7 Pages
scroll

No Preview Available !

OZ998 Даташит, Описание, Даташиты
FEATURES
SMBus, version 1.0, compliant
Intel PAS Protected Storage support
Support Pentium and x86-based designs
Support SMBus Q-Buffering via PWRGD
Support SMBus selector for dual/triple DIMMs
32KHZ input clock or Crystal input
Support 2 different power planes
10 bytes scratch pad registers
20 possible edge-sensitive programmable GPIOs
per device
8 possible Open Drain, Open Collector outputs
Programmable addresses for cascaded OZ998s
Supports 3.3V or 5V operation
Supports 5V tolerant LVTTL inputs (OZ998B)
LOW power hardware-driven speaker alarm
outputs
SMBALERT# and SMI event outputs
8 programmable interrupt inputs for SMI event or
SMBALERT#
8 Auto LED Flash (ALF) programmable outputs
with 10% or 50% duty cycles
ORDERING INFORMATION
OZ998S - 28 pin SSOP
OZ998
Intelligent Manager
Smart Multi-DIMM Selector
GENERAL DESCRIPTION
O2Micro’s OZ998 Multi-DIMM Selector supports the
switching between a primary SMBus and 3 other
secondary SMBus. This function is particularly useful
for DIMM devices and the support of Intel’s PAS
(Preboot Authentication Service).
In addition, the OZ998 can be configured to support
two different power planes with different sets of
General Purpose Input/Output (GPIO) signals, which
supplements and enhances the power management
capability of the chipsets, commonly found in an ACPI
(Advanced Configuration of Power Interface)
subsystem.
Up to 20 possible GPIOs are available per device,
and among those, GPIO[15:8] are programmable to
be either positive or negative-edged triggers to
generate an SMIEVENT/SMBALERT# to the system.
GPIO[7:0] are programmable to be either a regular
TTL level output, open drain or open collector output.
To support over 20 GPIOs through cascading multiple
OZ998 devices, configure each individual OZ998
device ID. Up to 8 Auto LED Flash (ALF) are available
to drive an LED or speaker at a programmable
frequency.
The OZ998 is packaged in a low profile, small 28 pin
SSOP.
07/13/00
©Copyright 2000 by O2Micro
OZ998-SF-2.2
All Rights Reserved
Page 1









No Preview Available !

OZ998 Даташит, Описание, Даташиты
PIN DIAGRAM
P_SMBCLK
P_SMBDATA
PWRGD
RESET#
GPIO[16]/S_SMBCLK1
GPIO[17]/S_SMBDATA1
GPIO[18]/S_SMBCLK2
GPIO[19]/S_SMBDATA2
GPIO[0]/SMIEVENT/ID[0]
GPIO[1]/ID[1]
GPIO[2]/SMBALERT#/ID[2]
GPIO[3]/ID[3]
GPIO[4]/ID[4]
GND
OZ998
1 28
2 27
3 26
4 25
5 24
6 23
7 22
8 21
9 20
10 19
11 18
12 17
13 16
14 15
OZ998
VCC
XIN/32KHZ
XOUT
GPIO[15]/S_SMBCLK3
GPIO[14]/S_SMBDATA3
GPIO[13]/SMB_SEL[1]
GPIO[12]/SMB_SEL[0]
GPIO[11]
GPIO[10]
GPIO[9]
GPIO[8]
GPIO[7]/ID[7]
GPIO[6]/ID[6]
GPIO[5]/ID[5]
OZ998-SF-2.2
Page 2









No Preview Available !

OZ998 Даташит, Описание, Даташиты
OZ998
PIN DESCRIPTION
Name
P_SMBCLK
P_SMBDATA
PWRGD
RESET#
GPIO[16]/
S_SMBCLK1
GPIO[17]/
S_SMBDATA1
GPIO[18]/
S_SMBCLK2
GPIO[19]/
S_SMBDATA2
GPIO[0]/
SMIEVENT/ID[0]
GPIO[1]/ID[1]
Pin Type
Input
Drive
Definition
No.
1
I
3.3V/5V Ext-PU
-
Primary SMBus Clock Input
Primary SMBus Clock Input for SMBus protocol communication.
2 I/O 3.3V/5V Ext-PU 12mA
Primary SMBus Data I/O
Primary SMBus Data Input/Output for SMBus protocol communication.
3I
TTL -
Host System Power Good
This pin indicates that the host systems power, including the Core Logic chipsets, is stable. Before the
host systems power is stable, this input pin will tri-state the output pins, GPO[19:8], from OZ998 while
GPO[7:0] will maintain its original value. Upon PWRGD going Low, the Secondary SMBus will be
disconnected from the Primary SMBus.
4I
TTL -
Reset
This active low pin will reset the OZ998.
5 I/O
TTL 4mA
General Purpose I/O/
Secondary SMBus-1 Clock I/O
Fully programmable GPIO that can be used for a variety of dedicated or specific functions. Pin GPIO[16] is
defaulted as an input. It is programmable to function as GPI[16] input, GPO[16] output or secondary
SMBus-1 Clock Input/Output. Refer to GPIO[19:16] Config.1&2 Registers for more details and GPIO
Config. Tables (section 8) for input/output selections.
6 I/O
TTL 4mA
General Purpose I/O/
Secondary SMBus-1 Data I/O
Fully programmable GPIO that can be used for a variety of dedicated or specific functions. Pin GPIO[17] is
defaulted as an input. It is programmable to function as GPI[17] input, GPO[17] output or secondary
SMBus-1 Data Input/Output. Refer to GPIO[19:16] Config.1&2 Registers for more details and GPIO Config.
Tables (section 8) for input/output selections.
7 I/O
TTL 4mA
General Purpose I/O/
Secondary SMBus-2 Clock I/O
Fully programmable GPIO that can be used for a variety of dedicated or specific functions. Pin GPIO[18] is
defaulted as an input. It is programmable to function as GPI[18] input, GPO[18] output or secondary
SMBus-2 Clock Input/Output. Refer to GPIO[19:16] Config.1&2 Registers for more details and GPIO
:Config. Tables (section 8) for input/output selections. Note: OZ998A GPIO [19:18] need 47k pull-up for
normal operation, OZ998B doesn’t.
8 I/O
TTL 4mA
General Purpose I/O /
Secondary SMBus-2 Data I/O
Fully programmable GPIO that can be used for a variety of dedicated or specific functions. Pin GPIO[19] is
defaulted as an input. It is programmable to function as GPI[19] input, GPO[19] output or secondary
SMBus-2 Data Input/Output. Refer to GPIO[19:16] Config.1&2 Registers for more details and GPIO Config.
:Tables (section 8) for input/output selections. Note: OZ998A GPIO [19:18] need 47k pull-up for normal
operation, OZ998B doesn’t.
9 I/O
TTL 12mA
General Purpose I/O /
SMIEVENT
Fully programmable GPIO that can be used for a variety of dedicated or specific functions. Pin GPIO[0] has
an SMIEVENT output as an alternate function. GPIO[0] is set as default. It is also programmable to
function as GPI[0] input, GPO[0] output, ALF[0] output, or ID[0] input. In addition, if this pin is configured as
output, TTL output, Open Drain or Open collector output can be selected. Refer to GPIO Config.1&2
Registers for more details and GPIO Config. Tables (section 8) for input/output selections.
10 I/O
TTL 12mA
General Purpose I/O
GPIO[2]/
SMBALERT#/ID[2]
Fully programmable GPIO that can be used for a variety of dedicated or specific functions. GPIO[1] pin
defaults as input. It is also programmable to function as GPI[1] input, GPO[1] output, ALF[1] output, or ID[1]
input. In addition, if this pin is configured as output, TTL output, Open Drain or Open collector output can
be selected. Refer to GPIO Config.1&2 Registers for more details and GPIO Config. Tables (section 8) for
input/output selections.
11 I/O
TTL 12mA
General Purpose I/O/
SMBALERT#
Fully programmable GPIO that can be used for a variety of dedicated or specific functions. Pin GPIO[2]
defaults as input. This pin, when programmed as an alternate function, can generate the SMBALERT#
interrupt. SMBALERT# is an interrupt service request signal to the SMBus Host which can be generated by
all devices connected to the OZ998. Pin GPIO[2]/SMBALERT# is also programmable to function as GPI[2]
input, GPO[2] output, ALF[2] output, or ID[2] input. In addition, if this pin is configured as output, TTL
output, Open Drain or Open collector can be selected. Refer to GPIO Config.1&2 Registers for more
details and GPIO Config. Tables (section 8) for I/O selections.
OZ998-SF-2.2
Page 3










Скачать PDF:

[ OZ998.PDF Даташит ]

Номер в каталогеОписаниеПроизводители
OZ990Intelligent Manager Smart PMU/GPIOO2Micro
O2Micro
OZ9901(OZ99xx) Intelligent LightingO2Micro
O2Micro
OZ9902(OZ99xx) Intelligent LightingO2Micro
O2Micro
OZ9902B(OZ99xx) Intelligent LightingO2Micro
O2Micro

Номер в каталоге Описание Производители
TL431

100 мА, регулируемый прецизионный шунтирующий регулятор

Unisonic Technologies
Unisonic Technologies
IRF840

8 А, 500 В, N-канальный МОП-транзистор

Vishay
Vishay
LM317

Линейный стабилизатор напряжения, 1,5 А

STMicroelectronics
STMicroelectronics

DataSheet26.com    |    2020    |

  Контакты    |    Поиск