DataSheet26.com

SA8803 PDF даташит

Спецификация SA8803 изготовлена ​​​​«Sames» и имеет функцию, называемую «LIGHT EMITTING DIODE DRIVER».

Детали детали

Номер произв SA8803
Описание LIGHT EMITTING DIODE DRIVER
Производители Sames
логотип Sames логотип 

10 Pages
scroll

No Preview Available !

SA8803 Даташит, Описание, Даташиты
sames
SA8803
LIGHT EMITTING DIODE DRIVER
FEATURES
n Drives 24 LED's under control of Serial n 11 Bit Information word controls up to
Interface
192 LED's (using eight SA8803s)
n Light Emitting Diode intensity n Readback of LED status
programmable using a single resistor n Requires a local clock of 8 times the
n Automatic lamp test facility on reset
data rate
(MRST)
n Constant current from power supply
n Minimal external components
option
n LED intensity constant, regardless of
number of LED's illuminated
DESCRIPTION
PIN CONNECTIONS
The block Diagram of the SA8803 is shown in
Fig. 1. A control word is clocked into the
device via the DATA pin with a local clock
provided to pin CLK. The control word
comprises a 3-bit chip address, a 5-bit LED
address and a Status (on/off) bit. Provided
that the Chip Adress matches the setting on
pins AD0..AD2 then the LED State Register is
addressed and the state of the selected LED
is set according to the Status bit in the Control
word.
The LEDs are driven by banks of Constant
Current Sources in which the value of the
current in all six banks is set by a single
external resistor connected between pin
INTENS and VEE. The total current drained
by the device and the LEDs may be fixed at
six times the LED current by connecting pin
CC to GND.
LED 1 7
LED 2 8
LED 3 9
LED 4 10
V EE 11
LED 5 12
LED 6 13
LED 7 14
V DD 15
LED 8 16
LED 9 17
6 5 4 3 2 1 44 43 42 41 40
39 TEST
38 LED 24
37 LED 23
36 LED 22
SA8803
35 V EE
34 LED 21
33 LED 20
32 LED 19
31 V DD
30 LED 18
29 LED 17
18 19 20 21 22 23 24 25 26 27 28
The status of all LEDs can be verified at any
time by pulling the TEST pin low. When tis
happens the contents of the LED Status
Register are clocked out of the SA8803 on the
pin DOUT. An additional test feature is that
al LEDs are illuminated for a short period after
power up to simplify system testing.
DR-00593
4159
PDS039-SA8803-001
1/10
REV. C 07-03-96









No Preview Available !

SA8803 Даташит, Описание, Даташиты
SA8803
FIGURE 1: BLOCK DIAGRAM
INTENS
CC
DATA
START
BIT
DETECTION
CLK CLOCK SCLK
SYNC
AD0....AD2
MRST
TEST
DR-00594
SIN
CLK 11 - BIT SHIFT REGISTER
RESET
START
BIT
3-BIT STOP
CHIP BIT
ADDRESS
COMPARATOR
LED
ADDRESS
DECODER
LED
SELECTION
BUS
24-BIT
LED
STATE
REGISTER
LED
DRIVERS
RESET
LAMP TEST
LOGIC
TEST
CONTROL
LOGIC
LED1
LED24
DOUT
2/10 sames









No Preview Available !

SA8803 Даташит, Описание, Даташиты
SA8803
PIN DESCRIPTION
Pin Designation
1..3 AD0..AD2
Description
Device address input pins. The binary code set up on
these pins, must match the address field of the control
word, before device access may be achieved. These
Schmitt-triggered inputs have on-chip pull-up resistors.
4 DOUT
This output is used for the manufacturers test requirements
and MUST be left open.
5
7..10,
12..14,
16..18,
20..21,
24..26
28..30
32..34,
36..38
CC
LED1..LED4,
LED5..LED7
LED8..LED10,
LED11..LED12,
LED13..LED15,
LED16..LED18,
LED19..LED21,
LED22..LED24
Constant Current Drain Select.This Schmitt-triggered
input has on-chip pullup provided.
High current LED drive terminal outputs.
22 INTENS
39 TEST
This analog input is used to set the drive current supplied
to the LED's. A resistor is connected from this pin to VEE.
Active low input that enables the internal LED status word
to be output from the DOUT pin. This Schmitt-triggered
input has on-chip pullup provided.
40 NC
41 CLK
Internally Unconnected.
External clock Schmitt-triggered input runs at 8X the data
rate (Baud rate).
42 MRST
This active low Schmitt-Trigger input may be used to
reset all internal registers. When active (low) this input
will cause all LED's to be driven for the duration of MRST
(lamp test). When MRST goes inactive all LED's will be
turned off. On-chip pullup provided.
43 GND
0V Supply Input for logic (0V)
44 DATA
11, 19, VEE
27, 35
Serial data input. Accept data in the form of an 11-bit
information word. This Schmitt-triggered input has on-
chip pullup provided.
Negative Supply Inputs (-5V)
6, 15, VDD
23, 31
Positive Supply Inputs (+5V)
Note: All inputs and outputs are CMOS compatible, unless otherwise specified.
sames
3/10










Скачать PDF:

[ SA8803.PDF Даташит ]

Номер в каталогеОписаниеПроизводители
SA8803LIGHT EMITTING DIODE DRIVERSames
Sames
SA8806A64 SEGMENT LIQUID CRYSTAL DISPLAY DRIVER PARALLEL INTERFACESames
Sames
SA8806AFA64 SEGMENT LIQUID CRYSTAL DISPLAY DRIVER PARALLEL INTERFACESames
Sames
SA8806APA64 SEGMENT LIQUID CRYSTAL DISPLAY DRIVER PARALLEL INTERFACESames
Sames

Номер в каталоге Описание Производители
TL431

100 мА, регулируемый прецизионный шунтирующий регулятор

Unisonic Technologies
Unisonic Technologies
IRF840

8 А, 500 В, N-канальный МОП-транзистор

Vishay
Vishay
LM317

Линейный стабилизатор напряжения, 1,5 А

STMicroelectronics
STMicroelectronics

DataSheet26.com    |    2020    |

  Контакты    |    Поиск