|
|
Número de pieza | SE103 | |
Descripción | LightCharger 2.5 Gb/s Transimpedance Amplifier LP Final | |
Fabricantes | SiGe Semiconductor Inc. | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de SE103 (archivo pdf) en la parte inferior de esta página. Total 9 Páginas | ||
No Preview Available ! SE1030W
LightCharger™ 2.5 Gb/s Transimpedance Amplifier
Final
Applications
§ SONET/SDH-based transmission systems, test
equipment and modules
§ OC-48 fibre optic modules and line termination
§ ATM optical receivers
§ Gigabit Ethernet
§ Fibre Channel
Features
§ Single +3.3 V power supply
§ Input noise current = 360 nA rms when used with
a 0.5 pF detector
§ Transimpedance gain = 2.3 kΩ into a 50 Ω load
(differential)
§ On-chip automatic gain control gives input
current overload of 2.6 mA pk and max output
voltage swing of 300 mV pk-pk
§ Differential 50 Ω outputs
§ Bandwidth (-3 dB) = 2.4 GHz
§ Wide data rate range = 50 Mb/s to 2.5 Gb/s
§ Constant photodiode reverse bias voltage = 1.5 V
(anode to input, cathode to VCC)
§ Minimal external components, supply decoupling
only
§ Operating junction temperature range = -40°C to
+125°C
§ Equivalent to Nortel Networks AB89-A2A
Ordering Information
Type
SE1030W
Package
Bare Die
Remark
Shipped in
Waffle Pack
Functional Block Diagram
Product Description
SiGe Semiconductor offers a portfolio of optical
networking ICs for use in high-performance optical
transmitter and receiver functions, from 155 Mb/s up
to 12.5 Gb/s.
SiGe Semiconductor’s SE1030W is a fully integrated,
silicon bipolar transimpedance amplifier; providing
wideband, low noise preamplification of signal current
from a photodetector. It features differential outputs,
and incorporates an automatic gain control
mechanism to increase dynamic range, allowing input
signals up to 2.6 mA peak. A decoupling capacitor on
the supply is the only external circuitry required. A
system block diagram is shown after the functional
description, on page 3.
Noise performance is optimized for 2.5 Gb/s
operation, with a calculated rms noise based
sensitivity of –26 dBm for 10-10 bit error rate, achieved
using a detector with 0.5 pF capacitance and a
responsivity of 0.9 A/W, with an infinite extinction ratio
source.
SE1030
TzAmp
2.5 Gb/s
VCC or +ve supply
Automatic Gain Control
Integrator
Rectifier
Input
Current
TZ_IN
Rf
Tz Amp
Bandgap
Reference
Output
Driver
50 Ω
50 Ω
OUTP
OUTN
43-DST-01 § Rev 1.5 § May 24/02
1 of 9
1 page SE1030W
LightCharger™ 2.5 Gb/s Transimpedance Amplifier
Final
AC Electrical Characteristics
Symbol
Parameter
Min Typ Max
BW (3dB) Small Signal Bandwidth at –3dB point
1.8 2.4
Tz
Differential Transimpedance (50 Ω on each output,
1.6
2.3
3.1
f = 100 MHz)
Dri Input Data Rate
50 2500
Voutmax
Flf
Maximum Differential Output Voltage
Low Frequency Cut-off
300
5
lOL
Pol
Nrms
Input Current before overload (2.5 Gb/s NRZ data)
Optical Overload
Input Noise Current (in 2 GHz)
2600
+1.6
360
500
DC and AC electrical characteristics are specified under the following conditions:
Supply Voltage (VCC).........................................3.1 V to 3.5 V
Junction Temperature (Tj)..................................–40°C to 125°C
Load Resistor (RL)...............................................50 Ω AC coupled via 220 nF, for each output
Photodetector Capacitance (Cd).......................0.5 pF
Input bond wire inductance................................1 nH
Photodetector responsivity.................................0.9 A/W
Transimpedance (Tz) measured with 4 µA mean photocurrent
Unit
GHz
kΩ
Mb/s
mV pk-pk
kHz
µA pk-pk
dBm
nA rms
43-DST-01 § Rev 1.5 § May 24/02
5 of 9
5 Page |
Páginas | Total 9 Páginas | |
PDF Descargar | [ Datasheet SE103.PDF ] |
Número de pieza | Descripción | Fabricantes |
SE1000W | LightChargerTM155 Mb/s Transimpedance Amplifier Final | SiGe Semiconductor Inc. |
SE1010W | LightChargerTM 622 Mb/s Transimpedance Amplifier Final | SiGe Semiconductor Inc. |
SE1020W | 1.25 Gb/s Transimpedance Amplifier Product Preview | SiGe Semiconductor Inc. |
SE103 | LightCharger 2.5 Gb/s Transimpedance Amplifier Final | SiGe Semiconductor Inc. |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |