|
|
PDF NCS2510 Data sheet ( Hoja de datos )
| Número de pieza | NCS2510 | |
| Descripción | 1.0 GHz Current Feedback Op Amp with Enable Feature | |
| Fabricantes | ON Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de NCS2510 (archivo pdf) en la parte inferior de esta página. Total 14 Páginas | ||
|
No Preview Available !
NCS2510
Product Preview
1.0 GHz Current Feedback
Op Amp with Enable
Feature
NCS2510 is a 1.0 GHz current feedback monolithic operational
amplifier featuring high slew rate and low differential gain and phase
error. The current feedback architecture allows for a superior
bandwidth and low power consumption. This device features an
enable pin.
Features
• −3.0 dB Small Signal BW (AV = +2.0, VO = 0.5 Vp−p) 1.0 GHz Typ
• Slew Rate 1500 V/ms
• Supply Current 8.5 mA
• Input Referred Voltage Noise 6.0 nV/ǸHz
• THD −60 dBc (f = 5.0 MHz, VO = 2.0 Vp−p)
• Output Current 150 mA
• Enable Pin Available
• Pin Compatible with AD8001
• Pb−Free Packages are Available
Applications
• High Resolution Video
• Line Driver
• High−Speed Instrumentation
• Wide Dynamic Range IF Amp
• Set Top Box
• NTSC/PAL/HDTV
3
Gain = +2
2 VS = ±5V
1 RF = 400W
RL = 150W
0
−1
−2
VOUT = 2.0V
−3
−4
−5
−6
0.01
VOUT = 1.0V
VOUT = 0.5V
0.1 1 10 100 1000
FREQUENCY (MHz)
Figure 1. Frequency Response:
Gain (dB) vs. Frequency
Av = +2.0
10k
This document contains information on a product under development. ON Semiconductor
reserves the right to change or discontinue this product without notice.
http://onsemi.com
8
1
SO−8
D SUFFIX
CASE 751
MARKING
DIAGRAMS
8
N2510
ALYW
G
1
6
1
SOT23−6
(TSOP−6)
SN SUFFIX
CASE 318G
6
YB1YW
G
1
YB1, N2510 = NCS2510
A = Assembly Location
L = Wafer Lot
Y = Year
W = Work Week
G = Pb−Free Package
SO−8 PINOUT
NC 1
−IN 2
+IN 3
VEE 4
−
+
8 EN
7 VCC
6 OUT
5 NC
(Top View)
SOT23−6 (TSOP−6) PINOUT
OUT 1
VEE 2
+IN 3
6 VCC
− 5 EN
4 −IN
(Top View)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 12 of this data sheet.
© Semiconductor Components Industries, LLC, 2005
July, 2005 − Rev. P0
1
Publication Order Number:
NCS2510/D
1 page  
NCS2510
DC ELECTRICAL CHARACTERISTICS (VCC = +5.0 V, VEE = −5.0 V, TA = −40°C to +85°C, RL = 150 W to GND, RF = 400 W,
AV = +2.0, Enable is left open, unless otherwise specified).
Symbol
Characteristic
Conditions
Min Typ Max Unit
DC PERFORMANCE
VIO Input Offset Voltage
DVIO/DT
Input Offset Voltage
Temperature Coefficient
IIB Input Bias Current
DIIB/DT
VIH
Input Bias Current
Temperature Coefficient
Input High Voltage (Enable)
(Note 4)
+Input (Non−Inverting), VO = 0 V
−Input (Inverting), VO = 0 V (Note 4)
+Input (Non−Inverting), VO = 0 V
−Input (Inverting), VO = 0 V
−5.0
2.5
0
6.0
"3.0
"6.0
+40
−10
+5.0
mV
mV/°C
mA
nA/°C
V
VIL Input Low Voltage (Enable)
(Note 4)
−2.5
V
INPUT CHARACTERISTICS
VCM
Input Common Mode Voltage
Range
"3.0
V
CMRR
RIN
CIN
Common Mode Rejection
Ratio
Input Resistance
Differential Input
Capacitance
(See Graph)
+Input (Non−Inverting)
−Input (Inverting)
55 dB
100 kW
50 W
1.0 pF
OUTPUT CHARACTERISTICS
ROUT
VO
Output Resistance
Output Voltage Range
IO Output Current
POWER SUPPLY
VS Operating Voltage Supply
Range
"90
0.1
"3.0
"120
10
W
V
mA
V
IS,ON
Power Supply Current −
Enabled
VO = 0 V
8.5 mA
IS,OFF
Power Supply Current −
Disabled
PSRR
Power Supply Rejection
Ratio
4. Guaranteed by design and/or characterization.
VO = 0 V
(See Graph)
0.11 mA
60 dB
http://onsemi.com
5
5 Page 
NCS2510
General Design Considerations
The current feedback amplifier is optimized for use in
high performance video and data acquisition systems. For
current feedback architecture, its closed−loop bandwidth
depends on the value of the feedback resistor. The
closed−loop bandwidth is not a strong function of gain, as is
for a voltage feedback amplifier, as shown in Figure 19.
10
RF = 300 W
5
RF = 400 W
0 RF = 500 W
RF = 600 W
−5
−10
AV = +2
−15 VCC = +5 V
VEE = −5 V
−20
0.1
1.0 10 100 1000
FREQUENCY (MHz)
Figure 19. Frequency Response vs. RF
10000
The −3.0 dB bandwidth is, to some extent, dependent on
the power supply voltages. By using lower power supplies,
the bandwidth is reduced, because the internal capacitance
increases. Smaller values of feedback resistor can be used at
lower supply voltages, to compensate for this affect.
Feedback and Gain Resistor Selection for Optimum
Frequency Response
A current feedback operational amplifier’s key advantage
is the ability to maintain optimum frequency response
independent of gain by using appropriate values for the
feedback resistor. To obtain a very flat gain response, the
feedback resistor tolerance should be considered as well.
Resistor tolerance of 1% should be used for optimum
flatness. Normally, lowering RF resistor from its
recommended value will peak the frequency response and
extend the bandwidth while increasing the value of RF
resistor will cause the frequency response to roll off faster.
Reducing the value of RF resistor too far below its
recommended value will cause overshoot, ringing, and
eventually oscillation.
Since each application is slightly different, it is worth
some experimentation to find the optimal RF for a given
circuit. A value of the feedback resistor that produces
X0.1 dB of peaking is the best compromise between
stability and maximal bandwidth. It is not recommended to
use a current feedback amplifier with the output shorted
directly to the inverting input.
Printed Circuit Board Layout Techniques
Proper high speed PCB design rules should be used for all
wideband amplifiers as the PCB parasitics can affect the
overall performance. Most important are stray capacitances
at the output and inverting input nodes as it can effect
peaking and bandwidth. A space (3/16″ is plenty) should be
left around the signal lines to minimize coupling. Also,
signal lines connecting the feedback and gain resistors
should be short enough so that their associated inductance
does not cause high frequency gain errors. Line lengths less
than 1/4″ are recommended.
Video Performance
This device designed to provide good performance with
NTSC, PAL, and HDTV video signals. Best performance is
obtained with back terminated loads as performance is
degraded as the load is increased. The back termination
reduces reflections from the transmission line and
effectively masks transmission line and other parasitic
capacitances from the amplifier output stage.
ESD Protection
All device pins have limited ESD protection using internal
diodes to power supplies as specified in the attributes table
(see Figure 20). These diodes provide moderate protection
to input overdrive voltages above the supplies. The ESD
diodes can support high input currents with current limiting
series resistors. Keep these resistor values as low as possible
since high values degrade both noise performance and
frequency response. Under closed−loop operation, the ESD
diodes have no effect on circuit performance. However,
under certain conditions the ESD diodes will be evident. If
the device is driven into a slewing condition, the ESD diodes
will clamp large differential voltages until the feedback loop
restores closed−loop operation. Also, if the device is
powered down and a large input signal is applied, the ESD
diodes will conduct.
NOTE: Human Body Model for +IN and –IN pins are
rated at 0.8kV while all other pins are rated at
2.0kV.
VCC
External
Pin
Internal
Circuitry
VEE
Figure 20. Internal ESD Protection
http://onsemi.com
11
11 Page | ||
| Páginas | Total 14 Páginas | |
| PDF Descargar | [ Datasheet NCS2510.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| NCS2510 | 1.0 GHz Current Feedback Op Amp with Enable Feature | ON Semiconductor |
| NCS2511 | 1 Ghz Current Feedback Op Amp | ON Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |