DataSheet26.com

HCPL3000 PDF даташит

Спецификация HCPL3000 изготовлена ​​​​«HP» и имеет функцию, называемую «Power Bipolar TransistorBase Drive Optocoupler».

Детали детали

Номер произв HCPL3000
Описание Power Bipolar TransistorBase Drive Optocoupler
Производители HP
логотип HP логотип 

9 Pages
scroll

No Preview Available !

HCPL3000 Даташит, Описание, Даташиты
Power Bipolar Transistor
Base Drive Optocoupler
Technical Data
H
HCPL-3000
Features
• High Output Current
IO2 (2.0 A Peak, 0.6 A
Continuous)
IO1 (1.0 A Peak, 0.5 A
Continuous)
• 1.5 kV/µs Minimum Common
Mode Rejection (CMR) at
VCM = 600 V
• Wide VCC Range (5.4 to 13
Volts)
• 2 µs Typical Propagation
Delay
• Recognized under UL 1577
for Dielectric Withstand
Proof Test Voltage of 5000
Vac, 1 Minute
Description
The HCPL-3000 consists of a
Silicon-doped GaAs LED optically
coupled to an integrated circuit
with a power output stage. This
optocoupler is suited for driving
power bipolar transistors and
power Darlington devices used in
motor control inverter applica-
tions. The high peak and steady
state current capabilities of the
output stage allow for direct
interfacing to the power device
without the need for an interme-
diate amplifier stage. With a CMR
Functional Diagram
rating of 1.5 kV/µs this optocoup-
ler readily rejects transients found
in inverter applications.
The LED controls the state of the
output stage. Transistor Q2 in the
output stage is on with the LED
off, allowing the base of the
power device to be held low.
Turning on the LED turns off
transistor Q2 and switches on
transistor Q1 in the output stage
which provides current to drive
the base of a power bipolar
device.
Applications
• Isolated Bipolar Transistor
Base Drive
• AC and DC Motor Drives
• General Purpose Industrial
Inverters
• Uninterruptable Power
Supply
ANODE 1
CATHODE 2
3
4
HCPL-3000
8 VCC
7 GND
Q2
6 VO2
Q1
5 VO1
TRUTH TABLE
LED OUTPUT
ON HIGH LEVEL
OFF LOW LEVEL
Q1
ON
OFF
Q2
OFF
ON
THE USE OF A 0.1µF BYPASS CAPACITOR CONNECTED BETWEEN PINS 8 AND 7 IS RECOMMENDED. ALSO, CURRENT LIMITING
RESISTORS ARE RECOMMENDED (SEE FIGURE 1, NOTE 2, AND NOTE 7).
CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to
prevent damage and/or degradation which may be induced by ESD.
5965-3584E
1-329









No Preview Available !

HCPL3000 Даташит, Описание, Даташиты
Schematic
1
ANODE
IF
+
-
CATHODE
2
I CC VCC
8
GND
Q2 7
Q1 IO2 6 VO2
IO1 VO1
5
Outline Drawing
0.65 (0.026)
1.05 (0.041)
0.90 (0.035)
1.50 (0.059)
TYPE
NUMBER
DATE
CODE
8
76
HP XXXX
YYWW
5
6.00 (0.236)
7.00 (0.276)
12 3 4
7.32 (0.288)
7.92 (0.312)
0°
13°
0.16 (0.006)
0.36 (0.014)
0°
13°
0.50
(0.020)
TYP
2.90 (0.114)
3.90 (0.154)
9.16 (0.361)
10.16 (0.400)
2.29 (0.090)
2.79 (0.110)
ANODE 1
HCPL-3000
8 VCC
3.00 (0.118)
4.00 (0.157)
CATHODE 2
3
2.55 (0.100)
3.55 (0.140)
4
7 GND
Q2
6 VO2
Q1
5 VO1
0.40 (0.016)
0.60 (0.024)
Regulatory Information
The HCPL-3000 has been
approved by the following
organizations:
UL
Recognized under UL 1577,
Component Recognition Program,
File E55361.
Demonstrated ESD
Performance
Human Body Model: MIL-STD-
883 Method 3015.7: Class 2
Machine Model: EIAJ IC-121-
1988 (1988.3.28 Version 2),
Test Method 20, Condition C:
1200 V
1-330









No Preview Available !

HCPL3000 Даташит, Описание, Даташиты
Insulation and Safety Related Specifications
Parameter
Symbol Value Units
Conditions
Min. External Air Gap
(External Clearance)
L(IO1) 6.0 mm Shortest distance measured through air, between
two conductive leads, input to output
Min. External Tracking L(IO2) 6.0 mm Shortest distance path measured along outside surface
Path (External Creepage)
of optocoupler body between the input and output leads
Min. Internal Plastic
Gap (Internal Clearance)
0.15 mm Through insulation distance conductor to conductor
inside the optocoupler cavity
Absolute Maximum Ratings
Parameter
Storage Temperature
Operating Temperature
Input Continuous Current
Reverse Voltage
Supply Voltage
Output 1 Continuous Current
Peak Current
Voltage
Output 2 Continuous Current
Peak Current
Output Power Dissipation
Total Power Dissipation
Lead Solder Temperature
Symbol
TS
TA
IF
VR
VCC
IO1
VO1
IO2
PO
PT
Min. Max. Unit
Conditions
Fig. Note
-55 125
°C
-20 80
°C
25 mA
91
6 V TA = 25°C
18 V
0.5 A
10,11 1
1.0 A Pulse Width < 5 µs,
Duty cycle = 1%
1
18 V
0.6 A
10,11,12 1
2.0 A Pulse Width < 5 µs, 12 1
Duty cycle = 1%
500 mW
10 1
550 mW
11 1
260°C for 10 s, 1.0 mm below seating plane
Recommended Operating Conditions
Parameter
Power Supply Voltage
Input Current (ON)
Input Current (OFF)
Operating Temperature
Symbol
VCC
IF(ON)
IF(OFF)
TA
Min.
5.4
8*
-
-20
*The initial switching threshold is 5 mA or less.
Max.
13
20
0.2
80
Units
V
mA
mA
°C
Recommended Protection
for Output Transistors
During switching transitions, the
output transistors Q1 and Q2 of
the HCPL-3000 can conduct large
amounts of current. Figure 1
describes a recommended circuit
design showing current limiting
resistors R1 and R2 which are
necessary in order to prevent
damage to the output transistors
Q1 and Q2 (see Note 7). A bypass
capacitor C1 is also recommended
to reduce power supply noise.
1-331










Скачать PDF:

[ HCPL3000.PDF Даташит ]

Номер в каталогеОписаниеПроизводители
HCPL3000Power Bipolar TransistorBase Drive OptocouplerHP
HP

Номер в каталоге Описание Производители
TL431

100 мА, регулируемый прецизионный шунтирующий регулятор

Unisonic Technologies
Unisonic Technologies
IRF840

8 А, 500 В, N-канальный МОП-транзистор

Vishay
Vishay
LM317

Линейный стабилизатор напряжения, 1,5 А

STMicroelectronics
STMicroelectronics

DataSheet26.com    |    2020    |

  Контакты    |    Поиск