DataSheet26.com

HA3-4905-5 PDF даташит

Спецификация HA3-4905-5 изготовлена ​​​​«Intersil Corporation» и имеет функцию, называемую «Precision Quad Comparators».

Детали детали

Номер произв HA3-4905-5
Описание Precision Quad Comparators
Производители Intersil Corporation
логотип Intersil Corporation логотип 

8 Pages
scroll

No Preview Available !

HA3-4905-5 Даташит, Описание, Даташиты
Data Sheet
HA-4900, HA-4902, HA-4905
September 1998 File Number 2855.3
Precision Quad Comparators
The HA-4900 series are monolithic, quad, precision
comparators offering fast response time, low offset voltage,
low offset current and virtually no channel-to-channel
crosstalk for applications requiring accurate, high speed,
signal level detection. These comparators can sense signals
at ground level while being operated from either a single +5V
supply (digital systems) or from dual supplies (analog
networks) up to ±15V. The HA-4900 series contains a unique
current driven output stage which can be connected to logic
system supplies (VLOGIC+ and VLOGIC-) to make the output
levels directly compatible (no external components needed)
with any standard logic or special system logic levels. In
combination analog/digital systems, the design employed in
the HA-4900 series input and output stages prevents
troublesome ground coupling of signals between analog and
digital portions of the system.
These comparators’ combination of features make them
ideal components for signal detection and processing in data
acquisition systems, test equipment and
microprocessor/analog signal interface networks.
For military grade product, refer to the HA-4902/883 data
sheet.
Pinout
HA-4900, HA-4902 (CERDIP)
HA-4905 (PDIP, CERDIP, SOIC)
TOP VIEW
VL+ 1
OUT 1 2
-IN 1 3
+IN 1 4
V- 5
+IN 2 6
-IN 2 7
OUT 2 8
-
+1
+
-2
16 OUT 4
- 15 -IN 4
4+ 14 +IN 4
13 V+
+ 12 +IN 3
3 - 11 -IN 3
10 OUT 3
9 VL-
Features
• Fast Response Time . . . . . . . . . . . . . . . . . . . . . . . . 130ns
• Low Offset Voltage . . . . . . . . . . . . . . . . . . . . . . . . . 2.0mV
• Low Offset Current . . . . . . . . . . . . . . . . . . . . . . . . . . .10nA
• Single or Dual Voltage Supply Operation
• Selectable Output Logic Levels
• Active Pull-Up/Pull-Down Output Circuit. No External
Resistors Required
Applications
• Threshold Detector
• Zero Crossing Detector
• Window Detector
• Analog Interfaces for Microprocessors
• High Stability Oscillators
• Logic System Interfaces
Ordering Information
PART
NUMBER
HA1-4900-2
HA1-4902-2
HA1-4905-5
HA3-4905-5
HA9P4905-5
TEMP RANGE
(oC)
PACKAGE
PKG. NO.
-55 to 125 16 Ld CERDIP F16.3
-55 to 125 16 Ld CERDIP F16.3
0 to 75
16 Ld CERDIP F16.3
0 to 75
16 Ld PDIP
E16.3
0 to 75
16 Ld SOIC
M16.3
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999









No Preview Available !

HA3-4905-5 Даташит, Описание, Даташиты
HA-4900, HA-4902, HA-4905
Absolute Maximum Ratings
Supply Voltage (Between V+ and V- Terminals) . . . . . . . . . . . . 33V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15V
Voltage Between VLOGIC+ and VLOGIC-. . . . . . . . . . . . . . . . . . .18V
Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50mA
Power Dissipation (Notes 1, 2)
Operating Conditions
Temperature Range
HA-4900-2, HA-4902-2. . . . . . . . . . . . . . . . . . . . . -55oC to 125oC
HA-4905-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 75oC
Thermal Information
Thermal Resistance (Typical, Note 3)
θJA (oC/W) θJC (oC/W)
CERDIP Package. . . . . . . . . . . . . . . . .
85
25
PDIP Package . . . . . . . . . . . . . . . . . . .
90
N/A
SOIC Package . . . . . . . . . . . . . . . . . . . 100
N/A
Maximum Junction Temperature (Ceramic Package) . . . . . . .175oC
Maximum Junction Temperature (Plastic Package) . . . . . . . . .150oC
Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC
(SOIC - Lead Tips Only)
Die Characteristics
Back Side Potential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V-
Number of Transistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Die Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 mils x 105 mils
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Maximum power dissipation, including output load, must be designed to maintain the junction temperature below 175oC for ceramic packages,
and below 150oC for plastic packages.
2. Total Power Dissipation (T.P.D.) is the sum of individual dissipation contributions of V+, V- and VLOGIC shown in curves of Power Dissipation
vs Supply Voltages (see Performance Curves). The calculated T.P.D. is then located on the graph of Maximum Allowable Package Dissipation
vs Ambient Temperature to determine ambient temperature operating limits imposed by the calculated T.P.D. (See Performance Curves). For
instance, the combination of +15V, -15V, +5V, 0V (V+, V-, VLOGIC+, VLOGIC-) gives a T.P.D. of 350mW, the combination +15V, -15V, +15V,
0V gives a T.P.D. of 450mW.
3. θJA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications
PARAMETER
VSUPPLY = 15V, VLOGIC+ = 5V, VLOGIC- = GND
TEMP
(oC)
HA-4900-2
-55oC to 125oC
MIN TYP MAX
HA-4902-2
-55oC to 125oC
MIN TYP MAX
HA-4905-5
0oC to 75oC
MIN TYP MAX
UNITS
INPUT CHARACTERISTICS
Offset Voltage (Note 4)
25 - 2 3 - 2 5 - 4 7.5 mV
Full - - 4 - - 8 - - 10 mV
Offset Current
25 - 10 25 - 10 35 - 25 50 nA
Full - - 35 - - 45 - - 70 nA
Bias Current (Note 5)
25
-
50 75
-
50 150
-
100 150
nA
Full - - 150 - - 200 - - 300 nA
Input Sensitivity (Note 6)
25
-
- VIO + -
- VIO + -
-
VIO +
mV
0.3 0.5 0.5
Full
-
- VIO + -
- VIO + -
-
VIO +
mV
0.4 0.6 0.7
Common Mode Range
Full V- - (V+) - V- - (V+) - V- - (V+) - V
2.4 2.6 2.4
Differential Input Resistance
25
- 250 -
- 250 -
- 250 -
M
TRANSFER CHARACTERISTICS
Large Signal Voltage Gain
25
- 400 -
- 400 -
- 400 - kV/V
Response Time (tPD(0))
(Note 7)
25
-
130 200
-
130 200
-
130 200
ns
Response Time (tPD(1))
(Note 7)
25
-
180 215
-
180 215
-
180 215
ns
2









No Preview Available !

HA3-4905-5 Даташит, Описание, Даташиты
HA-4900, HA-4902, HA-4905
Electrical Specifications VSUPPLY = 15V, VLOGIC+ = 5V, VLOGIC- = GND (Continued)
PARAMETER
TEMP
(oC)
HA-4900-2
-55oC to 125oC
MIN TYP MAX
HA-4902-2
-55oC to 125oC
MIN TYP MAX
HA-4905-5
0oC to 75oC
MIN TYP MAX
UNITS
OUTPUT CHARACTERISTICS
Output Voltage Level
Logic “Low State” (VOL) Full - 0.2 0.4 - 0.2 0.4 - 0.2 0.4 V
(Note 8)
Logic “High State” (VOH) Full 3.5 4.2 - 3.5 4.2 - 3.5 4.2 - V
(Note 8)
Output Current
ISINK
Full
ISOURCE
Full
POWER SUPPLY CHARACTERISTICS
3.0 -
3.0 -
- 3.0 -
- 3.0 -
- 3.0 -
- 3.0 -
- mA
- mA
Supply Current, IPS (+)
25
- 6.5 20 - 6.5 20 -
7 20 mA
Supply Current, IPS (-)
25 - 4 8 - 4 8 - 5 8 mA
Supply Current, IPS (Logic)
25
- 3.5 4
- 3.5 4
- 3.5 4 mA
Supply Voltage Range
VLOGIC+ (Note 2)
Full 0 - +15.0 0 - +15.0 0 - +15.0 V
VLOGIC- (Note 2)
Full
-15.0
-
0 -15.0 -
0 -15.0 -
0
V
NOTES:
4. Minimum differential input voltage required to ensure a defined output state.
5. Input bias currents are essentially constant with differential input voltages up to ±9V. With differential input voltages from ±9V to ±15V, bias cur-
rent on the more negative input can rise to approximately 500µA. This will also cause higher supply currents.
6. VCM = 0V. Input sensitivity is the worst case minimum differential input voltage required to guarantee a given output logic state. This parameter
includes the effects of offset voltage and voltage gain.
7. For tPD(1); 100mV input step, -10mV overdrive. For tPD(0); -100mV input step, 10mV overdrive. Frequency 100Hz; Duty Cycle 50%; Invert-
ing input driven. See Figure 1 for Test Circuit. All unused inverting inputs tied to +5V.
8. For VOH and VOL: ISINK = ISOURCE = 3.0mA. For other values of VLOGIC; VOH (Min) = VLOGIC + -1.5V.
Test Circuit and Waveform
+15V
+5V
-
DUT
+
VOUT
OVERDRIVE
tPD(0)
INPUT 100mV
VTH = 0V
tPD(1)
100mV
VTH = 0V
-15V
OVERDRIVE
OUTPUT
1.5V
tPD(0)
t=0
FIGURE 1.
t=0
1.5V
tPD(1)
3










Скачать PDF:

[ HA3-4905-5.PDF Даташит ]

Номер в каталогеОписаниеПроизводители
HA3-4905-5Precision Quad ComparatorsIntersil Corporation
Intersil Corporation

Номер в каталоге Описание Производители
TL431

100 мА, регулируемый прецизионный шунтирующий регулятор

Unisonic Technologies
Unisonic Technologies
IRF840

8 А, 500 В, N-канальный МОП-транзистор

Vishay
Vishay
LM317

Линейный стабилизатор напряжения, 1,5 А

STMicroelectronics
STMicroelectronics

DataSheet26.com    |    2020    |

  Контакты    |    Поиск