DataSheet26.com

S29CD-J PDF даташит

Спецификация S29CD-J изготовлена ​​​​«SPANSION» и имеет функцию, называемую «(S29CD-J / S29CL-J) Burst Mode Flash Memory».

Детали детали

Номер произв S29CD-J
Описание (S29CD-J / S29CL-J) Burst Mode Flash Memory
Производители SPANSION
логотип SPANSION логотип 

30 Pages
scroll

No Preview Available !

S29CD-J Даташит, Описание, Даташиты
www.DataSheet4U.com
S29CD-J & S29CL-J Flash Family
S29CD032J, S29CD016J, S29CL032J, S29CL016J
32/16 Megabit CMOS 2.6 Volt or 3.3 Volt-only
Simultaneous Read/Write, Dual Boot, Burst Mode
Flash Memory with VersatileI/O™
Data Sheet (Preliminary)
S29CD-J & S29CL-J Flash Family Cover Sheet
Notice to Readers: This document states the current technical specifications regarding the Spansion
product(s) described herein. The Preliminary status of this document indicates that product qualification has
been completed, and that initial production has begun. Due to the phases of the manufacturing process that
require maintaining efficiency and quality, this document may be revised by subsequent versions or
modifications due to changes in technical specifications.
Publication Number S29CD-J_CL-J_00
Revision B Amendment 1
Issue Date September 27, 2006









No Preview Available !

S29CD-J Даташит, Описание, Даташиты
Data Sheet (Preliminary)
Notice On Data Sheet Designations
Spansion Inc. issues data sheets with Advance Information or Preliminary designations to advise readers of
product information or intended specifications throughout the product life cycle, including development,
qualification, initial production, and full production. In all cases, however, readers are encouraged to verify
that they have the latest information before finalizing their design. The following descriptions of Spansion data
sheet designations are presented here to highlight their presence and definitions.
Advance Information
The Advance Information designation indicates that Spansion Inc. is developing one or more specific
products, but has not committed any design to production. Information presented in a document with this
designation is likely to change, and in some cases, development on the product may discontinue. Spansion
Inc. therefore places the following conditions upon Advance Information content:
“This document contains information on one or more products under development at Spansion Inc.
The information is intended to help you evaluate this product. Do not design in this product without
contacting the factory. Spansion Inc. reserves the right to change or discontinue work on this proposed
product without notice.”
Preliminary
The Preliminary designation indicates that the product development has progressed such that a commitment
to production has taken place. This designation covers several aspects of the product life cycle, including
product qualification, initial production, and the subsequent phases in the manufacturing process that occur
before full production is achieved. Changes to the technical specifications presented in a Preliminary
document should be expected while keeping these aspects of production under consideration. Spansion
places the following conditions upon Preliminary content:
“This document states the current technical specifications regarding the Spansion product(s)
described herein. The Preliminary status of this document indicates that product qualification has been
completed, and that initial production has begun. Due to the phases of the manufacturing process that
require maintaining efficiency and quality, this document may be revised by subsequent versions or
modifications due to changes in technical specifications.”
Combination
Some data sheets contain a combination of products with different designations (Advance Information,
Preliminary, or Full Production). This type of document distinguishes these products and their designations
wherever necessary, typically on the first page, the ordering information page, and pages with the DC
Characteristics table and the AC Erase and Program table (in the table notes). The disclaimer on the first
page refers the reader to the notice on this page.
Full Production (No Designation on Document)
When a product has been in production for a period of time such that no changes or only nominal changes
are expected, the Preliminary designation is removed from the data sheet. Nominal changes may include
those affecting the number of ordering part numbers available, such as the addition or deletion of a speed
option, temperature range, package type, or VIO range. Changes may also include those needed to clarify a
description or to correct a typographical error or incorrect specification. Spansion Inc. applies the following
conditions to documents in this category:
“This document states the current technical specifications regarding the Spansion product(s)
described herein. Spansion Inc. deems the products to have been in sufficient production volume such
that subsequent versions of this document are not expected to change. However, typographical or
specification corrections, or modifications to the valid combinations offered may occur.”
Questions regarding these document designations may be directed to your local sales office.
ii
S29CD-J & S29CL-J Flash Family
S29CD-J_CL-J_00_B1 September 27, 2006









No Preview Available !

S29CD-J Даташит, Описание, Даташиты
S29CD-J & S29CL-J Flash Family
S29CD032J, S29CD016J, S29CL032J, S29CL016J
32/16 Megabit CMOS 2.6 Volt or 3.3 Volt-only
Simultaneous Read/Write, Dual Boot, Burst Mode
Flash Memory with VersatileI/O™
Data Sheet (Preliminary)
General Description
The Spansion S29CD-J and S29CL-J devices are Floating Gate products fabricated in 110-nm process
technology. These burst-mode Flash devices are capable of performing simultaneous read and write
operations with zero latency on two separate banks, using separate data and address pins. These products
can operate up to 75 MHz (32 Mb) or 66 MHz (16 Mb), and use a single VCC of 2.5 V to 2.75 V (S29CD-J) or
3.0 V to 3.6 V (S29CL-J) that make them ideal for today’s demanding automotive applications.
Distinctive Characteristics
„ Single 2.6 V (S29CD-J) or 3.3 V (S29CL-J) for read/program/
erase
„ 110 nm Floating Gate Technology
„ Simultaneous Read/Write operation with zero latency
„ x32 Data Bus
„ Dual Boot Sector Configuration (top and bottom)
„ Flexible Sector Architecture
– CD016J & CL016J: Eight 2K Double word, Thirty-two 16K Double
word, and Eight 2K Double Word sectors
– CD032J & CL032J: Eight 2K Double word, Sixty-two 16K Double
Word, and Eight 2K Double Word sectors
„ VersatileI/O™ control (1.65 V to 3.6 V)
„ Programmable Burst Interface
– Linear for 2, 4, and 8 double word burst with or without wrap around
„ Secured Silicon Sector that can be either factory or customer
locked
„ 20 year data retention (typical)
„ Cycling Endurance: 1 million write cycles per sector (typical)
„ Command set compatible with JEDEC (JC42.4) standard
„ Supports Common Flash Interface (CFI)
„ Extended Temperature range
„ Persistent and Password methods of Advanced Sector
Protection
„ Unlock Bypass program command to reduce programming
time
„ ACC input pin to reduce factory programming time
„ Data Polling bits indicate program and erase operation
completion
„ Hardware (WP#) protection of two outermost sectors in the
large bank
„ Ready/Busy (RY/BY#) output indicates data available to
system
„ Suspend and Resume commands for Program and Erase
Operation
„ Offered Packages
– 80-pin PQFP
– 80-ball Fortified BGA
– Pb-free package option available
– Known Good Die
Performance Characteristics
Read Access Times
Speed Option (MHz)
75
(32 Mb only)
66
56
40
Max Asynch. Access Time, ns (tACC) 48 54 54 54
Max Synch. Burst Access, ns (tBACC) 7.5 (FBGA) 8 8 8
Min Initial Clock Delay (clock cycles) 5 4 4 3
Max CE# Access Time, ns (tCE)
Max OE# Access time, ns (tOE)
52 54 54 54
20 20 20 20
Current Consumption (Max values)
Continuous Burst Read @ 75 MHz
Program
Erase
Standby Mode
90 mA
50 mA
50 mA
60 µA
Typical Program and Erase Times
Double Word Programming
Sector Erase
18 µs
1.0 s
Publication Number S29CD-J_CL-J_00
Revision B Amendment 1
Issue Date September 27, 2006
This document states the current technical specifications regarding the Spansion product(s) described herein. The Preliminary status of this document indicates that product qual-
ification has been completed, and that initial production has begun. Due to the phases of the manufacturing process that require maintaining efficiency and quality, this document
may be revised by subsequent versions or modifications due to changes in technical specifications.










Скачать PDF:

[ S29CD-J.PDF Даташит ]

Номер в каталогеОписаниеПроизводители
S29CD-GSimultaneous Read/ Write Flash MemorySPANSION
SPANSION
S29CD-J(S29CD-J / S29CL-J) Burst Mode Flash MemorySPANSION
SPANSION

Номер в каталоге Описание Производители
TL431

100 мА, регулируемый прецизионный шунтирующий регулятор

Unisonic Technologies
Unisonic Technologies
IRF840

8 А, 500 В, N-канальный МОП-транзистор

Vishay
Vishay
LM317

Линейный стабилизатор напряжения, 1,5 А

STMicroelectronics
STMicroelectronics

DataSheet26.com    |    2020    |

  Контакты    |    Поиск