CDB5512 Datasheet PDF - Cirrus Logic
| Part Number | CDB5512 | |
| Description | (CDB5510 - CDB5513) Evaluation Board and Software | |
| Manufacturers | Cirrus Logic | |
| Logo |  |
|
|
There is a preview and CDB5512 download ( pdf file ) link at the bottom of this page. Total 22 Pages | ||
Preview 1 page No Preview Available !
www.DataSheet4U.com
CDB5510/11/12/13
CDB5510/11/12/13 Evaluation Board and Software
Features
! Supports the CS5510, CS5511, CS5512, and
CS5513 8-pin ADCs
! On-board Oscillator (CS5510/12)
! RS-232 Serial Communication with PC
! On-board Microcontroller
! On-board Voltage Reference
! LabWindows/CVI Evaluation Software
– Chip Control and Data Capture
– FFT Analysis
– Time Domain Analysis
– Noise Histogram Analysis
! Includes CDB551x, CS551X sample, and
Software
General Description
The CDB5510/11/12/13 is an inexpensive tool designed
to evaluate the performance of the CS5510/11/12/13 8-
pin Analog to Digital Converters. This document, as well
as the CS5510/11/12/13 data sheet should be read thor-
oughly before using the CDB5510/11/12/13 Evaluation
System.
The evaluation system consists of a CDB5510 Board
and PC software which allows the user to easily capture
and analyze data. The provided analysis functions in the
software include Time Domain Analysis, Histogram
Analysis, and Frequency Domain Analysis.
ORDERING INFORMATION:
CDB5510/11/12/13
Evaluation System
Includes CDB5510 and One Sample
VOLTAGE
REFERENCE
V+
VREF
V-
V-
AIN+
AIN-
V-
GND
V+
LEDs
DIP
SWITCHES
VREF
AIN+
AIN-
CS5510
CS5511
CS5512
CS5513
CS
SDO
SCLK
AT90S8515
MICROCONTROLLER
OSC.
CIRCUITRY
RESET
CIRCUITRY
CRYSTAL
3.6864 MHz
RS232
TRANS-
CEIVER
RS232
CONNECTOR
Preliminary Product Information
This document contains information for a new product.
Cirrus Logic reserves the right to modify this product without notice.
P.O. Box 17847, Austin, Texas 78760
(512) 445 7222 FAX: (512) 445 7581
http://www.cirrus.com
Copyright Cirrus Logic, Inc. 2001
(All Rights Reserved)
OCT ‘01
DS337DB2
1
|
| |
 
CDB5510/11/12/13
DIP switches on the CDB5510 should be set to the
“CS5511/13 Internally Clocked” section of Table
3.
1.6 PC Interface
The evaluation system comes with software and an
RS-232 cable to link the evaluation board to the
PC. The executable software was developed with
LabWindows/CVI and meant to run under Win-
dows 95 or 98. After installing the software, read
the readme.txt file for any last minute changes in
the software. Additionally, Section 2.0: Software
in this document further details how to install and
use the software.
1.7 Adding an Amplifier to the CDB5510
The CDB5510 is laid out so that a standard 8-pin
SOIC dual op-amp of the user’s choosing can be in-
stalled on the board to allow evaluation of the
CS5510/11/12/13’s performance with an op-amp
front-end. If an op-amp front-end is desired, the ad-
ditional components such as feedback resistors and
bypass capacitors must also be installed on the
board. A schematic of the amplifier section includ-
ing some typical component values is shown in
Figure 9. The amplifier is configured to operate in
either a single non-inverting, or a dual differential
configuration. The mode of operation can be select-
ed by changing the jumper on HDR2. Using the
components shown in Figure 9, the gain of the am-
plifier will be 10 in the single configuration, or 21
in the dual configuration. Different gain values can
be achieved by changing the value of resistors R6,
R17, and R18.
1.8 Interfacing to an External Controller
The ADC serial interface is SPI and MICROW-
IRETM compatible. The interface control lines (CS,
SDO, and SCLK) are connected to the 8515 micro-
controller on the CDB5510. The ADCs can be in-
terfaced to an external microcontroller through
HDR6 on the CDB5510. To accomplish this, the
CDB5510 board must be modified in one of three
ways: 1) remove the microcontroller from its sock-
et, 2) remove resistors R20-R22, or 3) cut the inter-
face control traces between the microcontroller and
the header.
DS337DB2
5
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for CDB5512 electronic component. |
| Information | Total 22 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ CDB5512.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| CDB5510 | The function is (CDB5510 - CDB5513) Evaluation Board and Software. Cirrus Logic | |
| CDB5511 | The function is (CDB5510 - CDB5513) Evaluation Board and Software. Cirrus Logic | |
| CDB5512 | The function is (CDB5510 - CDB5513) Evaluation Board and Software. Cirrus Logic | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
CDB5
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||