DataSheet26.com

NTE303A PDF даташит

Спецификация NTE303A изготовлена ​​​​«NTE Electronics» и имеет функцию, называемую «Silicone Heat Sink Compound».

Детали детали

Номер произв NTE303A
Описание Silicone Heat Sink Compound
Производители NTE Electronics
логотип NTE Electronics логотип 

5 Pages
scroll

No Preview Available !

NTE303A Даташит, Описание, Даташиты
MATERIAL SAFETY DATA SHEET
Finished Product
NTE303A
Silicone Heat Sink Compound
Date-Issued: Aug, 2005
MSDS Ref. No: NTE303A
Date-Revised: 2/2/2007
Revision No: New MSDS
I. PRODUCT AND SUPPLIER INFORMATION
PRODUCT NAME: NTE303A
Product Synonyms: Silicone Thermal Compound
Chemical family or Formula: Complex Mixture
Marketer:
NTE Electronics, Inc.
44 Farrand Street
Bloomfield, NJ 07003
Product Information:
973-748-5089
Transportation Emergency:
973-748-5089
Phone:
Fax:
Website:
Email:
MSDS number: NTE303A
Publication Date:
Replaces:
New
973-748-5089
973-748-6224
www.nteinc.com
Note: The purpose of this MSDS is to provide safe handling, shipping and disposal information for users of
the product. It is not intended to, nor does it, provide complete or extensive toxicological data on the
product or its components. Users who require this information are referred to primary suppliers of the
ingredients of interest.
II. COMPOSITION AND INFORMATION ON INGREDIENTS
Component Name
Silicone Fluid
CAS #
Proprietary information
Concentration
>20%
Zinc Oxide*
* Material in non-airborn form
1314-13-2
>60%
III. HAZARDS IDENTIFICATION
OSHA Hazard Classification:
No warning statements required.
Routes of Entry:
Inhalation, skin contact, ingestion
Chemical Interactions:
Avoid contact with all oxidizing agents









No Preview Available !

NTE303A Даташит, Описание, Даташиты
IV FIRST AID
Inhalation
Remove individual to fresh air. If not breathing, give artificial respiration or oxygen as appropriate.
Keep patient warm. Seek immediate medical advice.
Not an expected route of entry. Overexposure may cause irritation of the mucous membranes and
respiratory tract.
Skin Contact:
Flush skin thoroughly with soap and water. Rinse thoroughly. Seek medical advice if contact was
extensive. Prolonged direct skin contact may cause dermatitis or irritation.
Eyes:
Immediately flush eyes with plenty of water while holding eyelids apart. Seek immediate medical
advice
Overexposure to direct eye contact may cause redness, irritation, discomfort or tearing.
Ingestion:
May produce laxative effect.
Seek immediate medical advice. Never give anything by mouth to an unconscious person.
Not an expected route of exposure. Ingestion may cause abdominal pains, cramping, nausea or
vomiting.
Notes To Physician: Treat symptomatically.
V. FIRE FIGHTING MEASURES
Flammability Summary:
Heavy Grease
Flash Point: > 400 F
Fire/Explosion Hazards:
This material is not considered a potential fire and explosion hazard under normal operating conditions.
Extinguishing Media:
Foam, dry chemical, CO2. Water spray may be used to cool containers.
Do not allow, contaminated water to enter sewers or waterways.
Fire Fighting Instructions:
In case of fire, use normal fire fighting equipment including a NIOSH approved self-contained breathing
apparatus (SCBA). Use water to cool containers.
Hazardous Combustion Products:
Oxides of carbon.
1. ACCIDENTAL RELEASE MEASURES
Personal Protection for Emergency Situations:
Evacuate the area of all unnecessary personnel. Eliminate any ignition sources until the area is
determined to be free from explosion and fire hazards. Contain the release and eliminate its source if
this can be done safely.
Wear protective clothing. Keep unprotected persons away from spill.
Spill Mitigation Procedures
Air Release:
Low volatility makes this hazard unlikely.
Provide adequate ventilation. Keep away from ignition sources
Water Release:
Contain all liquid for treatment and/or disposal as a (potential) hazardous waste.
Notify all downstream users of possible contamination. Keep away from ignition sources.
Do not flush to sewer! US regulations (CERCLA) require reporting spills and releases to soil, water and
air in excess of stipulated quantities. US Coast Guard National Response Center is 800-424-8802.









No Preview Available !

NTE303A Даташит, Описание, Даташиты
Spill Mitigation Procedures (Cont’d)
Land Release:
Create a dike or trench to contain materials. Absorb spill with inert material (e.g., dry sand, clay, earth
or commercial absorbent), then place in a chemical waste container. Decontaminate all clothing and the
spill area using a detergent and flush with large amounts of water. Contain all contaminated water for
disposal and/or treatment.
Additional Spill Information:
Stop source of spill as soon as possible and notify appropriate personnel. Utilize emergency response
personal protection equipment prior to the start of any response. Evacuate all non-essential personnel.
Dispose of spill residues per guidelines under Section XIII, Disposal Considerations.
VII HANDLING AND STORAGE
Handling:
Do not take internally. Avoid contact with skin, eyes and clothing. Upon contact with skin or eyes, wash
with soap and water. Avoid breathing vapor or mist.
Storage
Keep container tightly closed. Store in a cool area away from ignition sources and oxidizers.
No special precautions need be taken if product is handled according to directions.
VIII EXPOSURE CONTROLS/ PERSONAL PROTECTION
Ventilation:
Local exhaust ventilation or other engineering controls are normally NOT necessary when handling or
using this product. General exhaust ventilation is usually sufficient for general worker safety and
comfort.
Explosion proof motors and fans are not required for unheated handling.
Respirator Type(s):
Air purifying respirators should not be used in oxygen deficient or IDLH atmospheres or if exposure
concentrations exceed ten (10) times the published limit.
Skin: Wear impervious gloves (butyl rubber, Viton, e.g.) to avoid skin contact. Follow good industrial hygiene
practices.
Eyes: Use chemical safety glasses with side shields, safety goggles and/or a full face shield where splashing
is possible.
Protective Clothing Type: Impervious
IX PHYSICAL AND CHEMICAL DATA
Physical State: Heavy grease
Color:
White
Odor:
Nil
Molecular Weight:
Not applicable to mixtures
pH (@ 25 Deg. C): Not applicable
Octanol/Water Coeff: No data
Solubility in Water: negligible
Bulk Density:
Not applicable
Specific Gravity (68 Deg.F): 2.2
Explosive limits:
No data. Low volatility makes ambient explosive
vapor concentrations impossible.
Vapor Density (Air = 1):
Vapor Pressure: (@ 20 Deg. C):
Evaporation Rate (Estimated):
Flash Point, (Estimated)
Volatiles % by vol.:
Approximate Boiling Point (deg.F):
Drop Point:
No data
<1
<1
> 400F
negligible
> 400
None










Скачать PDF:

[ NTE303A.PDF Даташит ]

Номер в каталогеОписаниеПроизводители
NTE303Thermal GreaseNTE Electronics
NTE Electronics
NTE3030LED IndicatorNTE Electronics
NTE Electronics
NTE3031Phototransistor Detector NPN-Si / Visible & IRNTE
NTE
NTE3032Phototransistor Detector NPN-Si / Visible & IRNTE
NTE

Номер в каталоге Описание Производители
TL431

100 мА, регулируемый прецизионный шунтирующий регулятор

Unisonic Technologies
Unisonic Technologies
IRF840

8 А, 500 В, N-канальный МОП-транзистор

Vishay
Vishay
LM317

Линейный стабилизатор напряжения, 1,5 А

STMicroelectronics
STMicroelectronics

DataSheet26.com    |    2020    |

  Контакты    |    Поиск