|
|
PDF NSPB346BS Data sheet ( Hoja de datos )
| Número de pieza | NSPB346BS | |
| Descripción | 120mW 5V 30mA nichia blue LED | |
| Fabricantes | Nichia Corporation | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de NSPB346BS (archivo pdf) en la parte inferior de esta página. Total 15 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
No. STSE-CB2097A
<Cat.No.020819>
SPECIFICATIONS FOR NICHIA BLUE LED
MODEL : NSPB346BS
NICHIA CORPORATION
-0-
1 page  
www.DataSheet4U.com
Nichia STSE-CB2097A
<Cat.No.020819>
7.CAUTIONS
(1) Lead Forming
· When forming leads, the leads should be bent at a point at least 3mm from the base of the epoxy bulb.
Do not use the base of the leadframe as a fulcrum during lead forming.
· Lead forming should be done before soldering.
· Do not apply any bending stress to the base of the lead. The stress to the base may damage the
characteristics or it may break the LEDs.
· When mounting the LEDs onto a printed circuit board, the holes on the circuit board should be
exactly aligned with the leads of the LEDs. If the LEDs are mounted with stress at the leads,
it causes deterioration of the epoxy resin and this will degrade the LEDs.
(2) Storage
· The LEDs should be stored at 30°C or less and 70%RH or less after being shipped from Nichia and
the storage life limits are 3 months. If the LEDs are stored for 3 months or more, they can be
stored for a year in a sealed container with a nitrogen atmosphere and moisture absorbent material.
· Nichia LED leadframes are comprised of a silver plated copper alloy. The silver surface
may be affected by environments which contain corrosive gases and so on. Please avoid conditions
which may cause the LED to corrode, tarnish or discolor. This corrosion or discoloration may cause
difficulty during soldering operations. It is recommended that the LEDs be used as soon as possible.
· Please avoid rapid transitions in ambient temperature, especially, in high humidity environments where
condensation can occur.
(3) Static Electricity
· Static electricity or surge voltage damages the LEDs.
It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs.
· All devices, equipment and machinery must be properly grounded. It is recommended that measures
be taken against surge voltage to the equipment that mounts the LEDs.
· When inspecting the final products in which LEDs were assembled, it is recommended to check
whether the assembled LEDs are damaged by static electricity or not. It is easy to find
static-damaged LEDs by a light-on test or a VF test at a lower current (below 1mA is recommended).
· Damaged LEDs will show some unusual characteristics such as the leak current remarkably
increases, the forward voltage becomes lower, or the LEDs do not light at the low current.
Criteria : (VF > 2.0V at IF=0.5mA)
-4-
5 Page 
Anode
Cathode
1.5MAX.
3
(2)
ITEM
RESIN(MOLD)
LENS COLOR
LEAD FRAME
MATERIALS
Epoxy Resin
Blue (Diffusion type)
Ag Plating Copper Alloy
Remark:
Bare copper alloy is exposed at tie-bar portion
after cutting.
The lamps have sharp and hard points that may
injure human eyes or fingers etc., so please pay
enough care in the handling.
1
6.2
26.5 ± 1
10 ± 0.5
Stopper
1
Model
NSPB346BS
NICHIA CORPORATION Title OUTLINE DIMENSIONS
No. 010831105781
Unit
mm
3/1
Scale
Allow
±0.2
11 Page | ||
| Páginas | Total 15 Páginas | |
| PDF Descargar | [ Datasheet NSPB346BS.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| NSPB346BS | NSPB346BS |  ETC |
| NSPB346BS | 120mW 5V 30mA nichia blue LED | Nichia Corporation |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |