|
|
PDF HFDOM40S3Rxxx Data sheet ( Hoja de datos )
| Número de pieza | HFDOM40S3Rxxx | |
| Descripción | 40Pin Flash Disk Module | |
| Fabricantes | Hanbit Electronics | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de HFDOM40S3Rxxx (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
HANBit
HFDOM40S3Rxxx
40Pin Flash Disk Module Min.16MB ~ Max.512MB,
True IDE Interface
1. PRODUCT OVERVIEW
GENERAL DESCRIPTION
The HFDOM40S3Rxxx series 40Pin Flash Disk Module is a flash technology based with True IDE interface flash
memory card. It is constructed with flash disk controller chip and NAND-type (Samsung) flash memory device. The
HFDOM40S3R-xxx series operates in both 3.3-Volt and 5.0-Volt power supplies. It comes in capacity of 16, 32, 48, 64, 80,
96, 128, 144, 160, 192, 208, 224, 256, 272,288, 320, 384 and up to 512MByte formatted 40Pin type .
www.DataSheet4UB.ycoomptimizing flash memory management, the life of this HFDOM40S3Rxxx series can be extended to its maximum level.
Because the ECC function is included, the correctness of data transfer between the HFDOM40S3Rxxx series and a True
IDE compatible interface device can be guaranteed.
The HFDOM40S3Rxxx series is fully compatible with applications such as CPU card / board, set top box, industry /
military PC / Notebook, security equipment, measuring instrument and embedded systems.
FEATURES
- ATA / True IDE compatible host interface
- ATA command set compatible
- Automatic sensing of PC Card ATA or true IDE host interface.
- Very high performance, very low power consumption
- Automatic error correction
- Auto Standby to save power consumption.
- Supports power down commands and sleep modes.
- Integrated PCMCIA attribute memory of 256 bytes (CIS)
- Support for 8 or 16 bit host transfers
- 3.3V/5.0V operation voltage
- Host Interface bus width : 8/16 bit Access
- Flash Interface bus width : 8 bit Access
- Capacity : Min. 16MB ~ Max. 512MB
- MTBF > 1,000,000 hours.
- Minimum 10,000 insertions.
- Shock : 2,000 G max.
- Vibration : 15 G peak to peak max.
PRODUCT SPECIFICATIONS
Capacities :
16, 32, 48, 64, 80, 96, 128, 144, 160, 192, 208, 224, 256, 272,288, 320, 384 and up to 512MB (formatted)
System Compatibility :
Please refer to the compatibility list of index.
Performance :
Host Data Transfer Rates :
up to 16.6 MB/sec, PIO mode 4; 16.6MB/sec
URL:www.hbe.co.kr
Rev. 1.0 (October, 2004)
1 / 31
HANBit Electronics Co., Ltd.
1 page  
HANBit
HFDOM40S3Rxxx
INSTALLTION GUIDE
1) Setting Method
① Make sure your computer is turned off before you open the case.
② Plug the carefully into the 40pin IDE slot on your computer.
Caution: Make sure to align pin1 on host adapter interface connector with pin 1 on your Flash Disk Module. Pin 1
is indicated by a triangle on the Flash Disk Module connector.
③ The Flash Disk Module is used power connector cable of the computer.
Caution: If you need to remove your Flash Disk Module, use both hands to pull it out carefully.
④ Check all cable connections and then replace your computer cover.
www.DataShee2t4)UB.cIoOmS setting Method
Before you format or partition your new drive, you must configure your computer's BIOS so that the computer can
recognize your new drive.
① Turn your computer on. As your computer start up, watch the screen for a message describing how to run the
system setup program on the screen (sometimes called BIOS or CMOS setup). This is usually done by pressing a
special key, such as Delete, Esc or F1 during startup. See your computer manual for details. Press the appropriate
key to run the system setup program.
② If your BIOS provides automatic drive detection (an "AUTO" drive type), select this option. ( We
recommend to use Normal / CHS mode to partition your Flash Disk Module to get the maximum formatted
capacity. )
This allows your computer to configure itself automatically for your new drive.
If your BIOS dose not provide “AUTO” drive detection, select "User-defined" drive setting and enter the
CHS values from the table. BIOS Settings (see specification) Capacity Cylinders Heads Sectors(unformatted)
③ Save the settings and exit the System Setup program. ( your computer will automatically reboot ) After you
configure your computer, you can use the standard DOS commands to partition and format your Flash Disk Module,
as described below.
3) Formatting Method
To partition your new Flash Disk Module with Microsoft DOS program :
① Insert a bootable DOS diskette into your diskette drive and restart your computer.
② Insert a DOS program diskette that contains the FDISK.EXE and FORMAT.COM
programs into your diskette drive. Use the same DOS version that is on your bootable diskette. At the A:\ > prompt,
type “FDISK” and press Enter.
③ Select “Create DOS partition or logical DOS drive” by pressing 1. Then press Enter.
④ Select “Create primary DOS partition” by pressing 1 again. Then press Enter.
Create your first drive partition. If you are creating a partition that will be used to boot your computer (drive C),
make sure that the partition is marked active.
⑤ Create an extended partition and additional logical drives as necessary, until all the space on your new hard drive
has been partitioned.
⑥ When the partitioning is complete, FDISK reboots your computer.
Caution: Make sure to use the correct drive letters so that you do not format a drive that already contains data.
⑦ At the A:\ > prompt, type “format c:/s”, where c is the letter of your first new partition, Repeat the format process
for all the new partitions you have created.
⑧ After you format your drive, it is ready to use.
URL:www.hbe.co.kr
Rev. 1.0 (October, 2004)
5 / 31
HANBit Electronics Co., Ltd.
5 Page 
HANBit
HFDOM40S3Rxxx
This register contains the numbers of sectors of data requested to be transferred on a read or
write operation between the host and the CompactFlash Storage Card. If the value in this register is zero, a count
of 256 sectors is specified. If the command was successful, this register is zero at command completion. If not
successfully completed, the register contains the number of sectors that need to be transferred in order to
complete the request.
BIT DESCRIPTION-
76543210
Sector Count
5) Sector Number (LBA 7-0) Register(Address–1F3h[173h];Offset 3)
This register contains the starting sector number or bits 7-0 of the Logical Block Address (LBA)
for any CompactFlash Storage Card data access for the subsequent command.
www.DataSheet4U.com
BIT DESCRIPTION - CHS
76543210
Sector (7: 0)
LBA
76543210
LBA (7 : 0)
6) Cylinder Low (LBA 15-8 )Register (Address–1F4h[174h];Offset 4)
This register contains the low order 8 bits of the starting cylinder address or bits 15-8 of the
Logical Block Address.
DIT DESCRIPTION-
CHS
7654321
Cylinder ( 7: 0 )
LBA
7654321
LBA ( 15 : 8 )
0
0
7) Cylinder High(LBA 23–16)Register(Address–1F5h[175h]; Offset 6)
This register contains the high order bits of the starting cylinder address or bits 23-16 of the
Logical Block Address.
BIT DESCRIPTION-
CHS
76543210
Cylinder ( 15 :8 )
LBA
76543210
LBA ( 23 : 16 )
8) Status/Alternate Status Register(Address 1F7h[177h]/3F6h[376h];Offset 7/ Eh)
These registers return the CompactFlash Storage Card status when read by the host. Reading
URL:www.hbe.co.kr
Rev. 1.0 (October, 2004)
11 / 31
HANBit Electronics Co., Ltd.
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet HFDOM40S3Rxxx.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| HFDOM40S3Rxxx | 40Pin Flash Disk Module | Hanbit Electronics |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |