DataSheet26.com

HFDOM44S3Vxxx PDF даташит

Спецификация HFDOM44S3Vxxx изготовлена ​​​​«Hanbit Electronics» и имеет функцию, называемую «44Pin Flash Disk Module».

Детали детали

Номер произв HFDOM44S3Vxxx
Описание 44Pin Flash Disk Module
Производители Hanbit Electronics
логотип Hanbit Electronics логотип 

29 Pages
scroll

No Preview Available !

HFDOM44S3Vxxx Даташит, Описание, Даташиты
HANBit
HFDOM44S3Vxxx
44Pin Flash Disk Module Min.16MB ~ Max.384MB,
True IDE Interface
1. PRODUCT OVERVIEW
GENERAL DESCRIPTION
The HFDOM44S3Vxxx series 44Pin Flash Disk Module is a flash technology based with True IDE interface flash
memory card. It is constructed with flash disk controller chip and NAND-type (Samsung) flash memory device. The
HFDOM44S3V-xxx series operates in both 3.3-Volt and 5.0-Volt power supplies. It comes in capacity of 16, 32, 48, 64, 80,
96, 128, 144, 160, 192, 256, 272,288, 320 and up to 384MByte formatted 44Pin type .
www.DataSheet4UB.ycoomptimizing flash memory management, the life of this HFDOM44S3Vxxx series can be extended to its maximum level.
Because the ECC function is included, the correctness of data transfer between the HFDOM44S3Vxxx series and a True
IDE compatible interface device can be guaranteed.
The HFDOM44S3Vxxx series is fully compatible with applications such as CPU card / board, set top box, industry /
military PC / Notebook, security equipment, measuring instrument and embedded systems.
FEATURES
- ATA / True IDE compatible host interface
- ATA command set compatible
- Automatic sensing of PC Card ATA or true IDE host interface.
- Very high performance, very low power consumption
- Automatic error correction
- Auto Standby to save power consumption.
- Supports power down commands and sleep modes.
- Integrated PCMCIA attribute memory of 256 bytes (CIS)
- Support for 8 or 16 bit host transfers
- 3.3V/5.0V operation voltage
- Host Interface bus width : 8/16 bit Access
- Flash Interface bus width : 8 bit Access
- Capacity : Min. 16MB ~ Max. 384MB
- MTBF > 1,000,000 hours.
- Minimum 10,000 insertions.
- Shock : 2,000 G max.
- Vibration : 15 G peak to peak max.
PRODUCT SPECIFICATIONS
Capacities :
16, 32, 48, 64, 80, 96, 128, 144, 160, 192, 256, 272,288, 320 and up to 384MB (formatted)
System Compatibility :
Please refer to the compatibility list of index.
Performance :
Host Data Transfer Rates :
up to 16.6 MB/sec, PIO mode 4; 16.6MB/sec
URL:www.hbe.co.kr
Rev. 1.0 (January, 2005)
1 / 29
HANBit Electronics Co., Ltd.









No Preview Available !

HFDOM44S3Vxxx Даташит, Описание, Даташиты
HANBit
Operating Voltage : 3.3V / 5.0V 10%
Power consumption : 3.3V ± 5%
Read mode
Write mode
Stop mode
<30 mA
<56 mA
<2 mA
Environment conditions :
www.DataSheet4U.com
Operating temperature
Storage temperature
Relative humidity
0°C to + 70°C
- °C to + °C
8% to 95%, non-condensing
HFDOM44S3Vxxx
ELECTRICAL SPECIFICATIONS
Table 1.1 Absolute Maximum Ratings
Symbol
VDD
VIN
VOUT
TSTG
Parameter
Power supply
Input voltage
Output voltage
Storage temperature
Rating
-0.3 to 3.6
-0.3 to VDD+0.3
-0.3 to VDD+0.3
-55 to 150
Units
V
V
V
oC
Table 1.2 Recommended Operating Conditions
Symbol
VDD
VIN
TOPR
Parameter
Power supply
Input voltage
Operating temperature
Min.
3.0
-0.3
0
Max.
3.6
VDD+0.3
70
Units
V
V
oC
Table 1.3 DC Characteristics
Sym.
VIL
VIH
VIL
VIH
VOL
VOH
RI
Parameter
Input low voltage
Input high voltage
Schmitt input low voltage
Schmitt input high voltage
Output low voltage
Output high voltage
Input pull up/down resistance
Min Typ
0.2
0.9
Vcc – 0.8
75
Max
0.2VDD
2.5
0.4
Units
V
V
V
V
V
V
k
URL:www.hbe.co.kr
Rev. 1.0 (January, 2005)
2 / 29
HANBit Electronics Co., Ltd.









No Preview Available !

HFDOM44S3Vxxx Даташит, Описание, Даташиты
HANBit
HFDOM44S3Vxxx
INSTALLTION GUIDE
1) Setting Method
Make sure your computer is turned off before you open the case.
Plug the carefully into the 44pin IDE slot on your computer.
Caution: Make sure to align pin1 on host adapter interface connector with pin 1 on your Flash Disk Module. Pin 1
is indicated by a triangle on the Flash Disk Module connector.
The Flash Disk Module is used power connector cable of the computer.
Caution: If you need to remove your Flash Disk Module, use both hands to pull it out carefully.
Check all cable connections and then replace your computer cover.
www.DataShee2t4)UB.cIoOmS setting Method
Before you format or partition your new drive, you must configure your computer's BIOS so that the computer can
recognize your new drive.
Turn your computer on. As your computer start up, watch the screen for a message describing how to run the
system setup program on the screen (sometimes called BIOS or CMOS setup). This is usually done by pressing a
special key, such as Delete, Esc or F1 during startup. See your computer manual for details. Press the appropriate
key to run the system setup program.
If your BIOS provides automatic drive detection (an "AUTO" drive type), select this option. ( We
recommend to use Normal / CHS mode to partition your Flash Disk Module to get the maximum formatted
capacity. )
This allows your computer to configure itself automatically for your new drive.
If your BIOS dose not provide “AUTO” drive detection, select "User-defined" drive setting and enter the
CHS values from the table. BIOS Settings (see specification) Capacity Cylinders Heads Sectors(unformatted)
Save the settings and exit the System Setup program. ( your computer will automatically reboot ) After you
configure your computer, you can use the standard DOS commands to partition and format your Flash Disk Module,
as described below.
3) Formatting Method
To partition your new Flash Disk Module with Microsoft DOS program :
Insert a bootable DOS diskette into your diskette drive and restart your computer.
Insert a DOS program diskette that contains the FDISK.EXE and FORMAT.COM
programs into your diskette drive. Use the same DOS version that is on your bootable diskette. At the A:\ > prompt,
type “FDISK” and press Enter.
Select “Create DOS partition or logical DOS drive” by pressing 1. Then press Enter.
Select “Create primary DOS partition” by pressing 1 again. Then press Enter.
Create your first drive partition. If you are creating a partition that will be used to boot your computer (drive C),
make sure that the partition is marked active.
Create an extended partition and additional logical drives as necessary, until all the space on your new hard drive
has been partitioned.
When the partitioning is complete, FDISK reboots your computer.
Caution: Make sure to use the correct drive letters so that you do not format a drive that already contains data.
At the A:\ > prompt, type “format c:/s”, where c is the letter of your first new partition, Repeat the format process
for all the new partitions you have created.
After you format your drive, it is ready to use.
URL:www.hbe.co.kr
Rev. 1.0 (January, 2005)
3 / 29
HANBit Electronics Co., Ltd.










Скачать PDF:

[ HFDOM44S3Vxxx.PDF Даташит ]

Номер в каталогеОписаниеПроизводители
HFDOM44S3Vxxx44Pin Flash Disk ModuleHanbit Electronics
Hanbit Electronics

Номер в каталоге Описание Производители
TL431

100 мА, регулируемый прецизионный шунтирующий регулятор

Unisonic Technologies
Unisonic Technologies
IRF840

8 А, 500 В, N-канальный МОП-транзистор

Vishay
Vishay
LM317

Линейный стабилизатор напряжения, 1,5 А

STMicroelectronics
STMicroelectronics

DataSheet26.com    |    2020    |

  Контакты    |    Поиск