DataSheet26.com

78F0547 PDF даташит

Спецификация 78F0547 изготовлена ​​​​«NEC» и имеет функцию, называемую «UPD78F0547».

Детали детали

Номер произв 78F0547
Описание UPD78F0547
Производители NEC
логотип NEC логотип 

70 Pages
scroll

No Preview Available !

78F0547 Даташит, Описание, Даташиты
User’s Manual
www.DataSheet4U.com
78K0/KF2
8-Bit Single-Chip Microcontrollers
µPD78F0544
µPD78F0545
µPD78F0546
µPD78F0547
µPD78F0547D
µPD78F0544(A)
µPD78F0545(A)
µPD78F0546(A)
µPD78F0547(A)
The µPD78F0547D has an on-chip debug function.
Do not use this product for mass production because its reliability cannot be guaranteed after the on-chip debug function
has been used, due to issues with respect to the number of times the flash memory can be rewritten. NEC Electronics
does not accept complaints concerning this product.
Document No. U17397EJ4V0UD00 (4th edition)
Date Published May 2006 NS CP(K)
Printed in Japan
2005









No Preview Available !

78F0547 Даташит, Описание, Даташиты
[MEMO]
www.DataSheet4U.com
2 User’s Manual U17397EJ4V0UD









No Preview Available !

78F0547 Даташит, Описание, Даташиты
NOTES FOR CMOS DEVICES
www.DataSheet4U.com
1 VOLTAGE APPLICATION WAVEFORM AT INPUT PIN
Waveform distortion due to input noise or a reflected wave may cause malfunction. If the input of the
CMOS device stays in the area between VIL (MAX) and VIH (MIN) due to noise, etc., the device may
malfunction. Take care to prevent chattering noise from entering the device when the input level is fixed,
and also in the transition period when the input level passes through the area between VIL (MAX) and
VIH (MIN).
2 HANDLING OF UNUSED INPUT PINS
Unconnected CMOS device inputs can be cause of malfunction. If an input pin is unconnected, it is
possible that an internal input level may be generated due to noise, etc., causing malfunction. CMOS
devices behave differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed
high or low by using pull-up or pull-down circuitry. Each unused pin should be connected to VDD or GND
via a resistor if there is a possibility that it will be an output pin. All handling related to unused pins must
be judged separately for each device and according to related specifications governing the device.
3 PRECAUTION AGAINST ESD
A strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and
ultimately degrade the device operation. Steps must be taken to stop generation of static electricity as
much as possible, and quickly dissipate it when it has occurred. Environmental control must be
adequate. When it is dry, a humidifier should be used. It is recommended to avoid using insulators that
easily build up static electricity. Semiconductor devices must be stored and transported in an anti-static
container, static shielding bag or conductive material. All test and measurement tools including work
benches and floors should be grounded. The operator should be grounded using a wrist strap.
Semiconductor devices must not be touched with bare hands. Similar precautions need to be taken for
PW boards with mounted semiconductor devices.
4 STATUS BEFORE INITIALIZATION
Power-on does not necessarily define the initial status of a MOS device. Immediately after the power
source is turned ON, devices with reset functions have not yet been initialized. Hence, power-on does
not guarantee output pin levels, I/O settings or contents of registers. A device is not initialized until the
reset signal is received. A reset operation must be executed immediately after power-on for devices
with reset functions.
5 POWER ON/OFF SEQUENCE
In the case of a device that uses different power supplies for the internal operation and external
interface, as a rule, switch on the external power supply after switching on the internal power supply.
When switching the power supply off, as a rule, switch off the external power supply and then the
internal power supply. Use of the reverse power on/off sequences may result in the application of an
overvoltage to the internal elements of the device, causing malfunction and degradation of internal
elements due to the passage of an abnormal current.
The correct power on/off sequence must be judged separately for each device and according to related
specifications governing the device.
6 INPUT OF SIGNAL DURING POWER OFF STATE
Do not input signals or an I/O pull-up power supply while the device is not powered. The current
injection that results from input of such a signal or I/O pull-up power supply may cause malfunction and
the abnormal current that passes in the device at this time may cause degradation of internal elements.
Input of signals during the power off state must be judged separately for each device and according to
related specifications governing the device.
User’s Manual U17397EJ4V0UD
3










Скачать PDF:

[ 78F0547.PDF Даташит ]

Номер в каталогеОписаниеПроизводители
78F0544A8-Bit Single-Chip MicrocontrollersRenesas Electronics
Renesas Electronics
78F05458-Bit Single-Chip MicrocontrollersRenesas Electronics
Renesas Electronics
78F0545A8-Bit Single-Chip MicrocontrollersRenesas Electronics
Renesas Electronics
78F05468-Bit Single-Chip MicrocontrollersRenesas Electronics
Renesas Electronics

Номер в каталоге Описание Производители
TL431

100 мА, регулируемый прецизионный шунтирующий регулятор

Unisonic Technologies
Unisonic Technologies
IRF840

8 А, 500 В, N-канальный МОП-транзистор

Vishay
Vishay
LM317

Линейный стабилизатор напряжения, 1,5 А

STMicroelectronics
STMicroelectronics

DataSheet26.com    |    2020    |

  Контакты    |    Поиск