|
|
PDF HDR-HC3K Data sheet ( Hoja de datos )
| Número de pieza | HDR-HC3K | |
| Descripción | DIGITAL HD VIDEO CAMERA RECORDER SERVICE MANUAL | |
| Fabricantes | Sony | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de HDR-HC3K (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
HDR-HC3/HC3E/HC3K/HC3EK
RMT-831
SERVICE MANUAL
Ver 1.2 2006.08
Revision History
How to use
Acrobat Reader
N MECHANISM (MDX-N110)
Photo: HDR-HC3/Black
2LEVEL
US Model
Canadian Model
AEP Model
UK Model
North European Model
E Model
Australian Model
Chinese Model
Hong Kong Model
Korea Model
Tourist Model
Japanese Model
Link
SPECIFICATIONS
DISASSEMBLY
SCHEMATIC DIAGRAMS
MODEL INFORMATION TABLE
BLOCK DIAGRAMSwww.DataSheet.co.kr
PRINTED WIRING BOARDS
SERVICE NOTE
FRAME SCHEMATIC DIAGRAMS REPAIR PARTS LIST
The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part num-
ber specified.
Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
HDR-HC3/HC3E/HC3K/HC3EK_L2
9-876-939-31
DIGITAL HD VIDEO CAMERA RECORDER
Sony EMCS Co.
2006H0500-1
© 2006.8
Published by Kohda TEC
Datasheet pdf - http://www.DataSheet4U.net/
1 page  
ENGLISH JAPANESE
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
www.DataSheet.co.kr
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
2. Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
HDR-HC3/HC3E/HC3K/HC3EK_L2
—5—
Datasheet pdf - http://www.DataSheet4U.net/
5 Page 
ENGLISH JAPANESE
Self-diagnosis Code
Block Detailed
Function Code
Symptom/State
Correction
E 61
1
0
Zoom operations fault
(Cannot initialize zoom lens.)
Inspect the zoom MR sensor of lens block (Pin qh, qk of CN7103
on the LD-202 board) when zooming is performed when the zoom
switch is operated and the zoom motor drive circuit (IC7204 on
the LD-202 board) when zooming is not performed.
E 61
Focus lens initializing failure and zoom
1 1 lens initializing failure occur simulta- Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.
neously.
E 62
0
0
Steadyshot function does not work well.
(With pitch angular velocity sensor output
stopped.)
Inspect pitch angular velocity sensor (SE7702 on the CM-071
board) peripheral circuits.
E 62
0
1
Steadyshot function does not work well.
(With yaw angular velocity sensor output
stopped.)
Inspect yaw angular velocity sensor (SE7701 on the CM-071
board) peripheral circuits.
E 9 1 0 1 Abnormality when flash is being charged. Checking of flash unit or replacement of flash unit. (Note)
Note: After repair, be sure to perform “1-6. PROCESS AFTER FIXING FLASH ERROR”.
1-6. PROCESS AFTER FIXING FLASH ERROR
When “FLASH error” (Self-diagnosis Code E:91:**) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash is
changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Connect the adjustment remote commander (RM-95 or NEW LANC JIG) and perform the
following process.
Order Page Address Data
Procedure
17
27
37
01 75
00 01 Press PAUSE (Write) button.
02 Check the data changes to “01”.
www.DataSheet.co.kr
HDR-HC3/HC3E/HC3K/HC3EK_L2
1-4
Datasheet pdf - http://www.DataSheet4U.net/
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet HDR-HC3K.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| HDR-HC3 | DIGITAL HD VIDEO CAMERA RECORDER SERVICE MANUAL | Sony |
| HDR-HC3E | DIGITAL HD VIDEO CAMERA RECORDER SERVICE MANUAL | Sony |
| HDR-HC3EK | DIGITAL HD VIDEO CAMERA RECORDER SERVICE MANUAL | Sony |
| HDR-HC3K | DIGITAL HD VIDEO CAMERA RECORDER SERVICE MANUAL | Sony |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |