|
|
Número de pieza | N154Z3-L01 | |
Descripción | TFT LCD Module | |
Fabricantes | CMI MEI | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de N154Z3-L01 (archivo pdf) en la parte inferior de esta página. Total 28 Páginas | ||
No Preview Available ! Doc. No.: 44082127
Issued Date: Apr. 23, 2008
Model No.: N154Z3 - L01
Preliminary
TFT LCD Preliminary Specification
MODEL NO.: N154Z3 - L01
Customer :
Approved by :
Note :
www.DataSheet.net/
annie_hsu(
2008-04-30 PMMD III
15:55:27 CST Director
/56522 /
54873)
Director Accept
1 / 28
Version 1.1
Datasheet pdf - http://www.DataSheet4U.co.kr/
1 page Doc. No.: 44082127
Issued Date: Apr. 23, 2008
Model No.: N154Z3 - L01
Preliminary
2. ABSOLUTE MAXIMUM RATINGS
2.1 ABSOLUTE RATINGS OF ENVIRONMENT
Item
Storage Temperature
Operating Ambient Temperature
Shock (Non-Operating)
Vibration (Non-Operating)
Symbol
TST
TOP
SNOP
VNOP
Value
Min. Max.
-20 +60
0 +50
- 200/2
- 1.5
Note (1) Temperature and relative humidity range is shown in the figure below.
(a) 90 %RH Max. (Ta 40 ºC).
(b) Wet-bulb temperature should be 39 ºC Max. (Ta > 40 ºC).
(c) No condensation.
Note (2) The temperature of panel surface should be 0 ºC Min. and 50 ºC Max.
Relative Humidity (%RH)
100
90
80
Unit
ºC
ºC
G/ms
G
Note
(1)
(1), (2)
(3), (5)
(4), (5)
60
Operating Range
40
www.DataSheet.net/
20
10 Storage Range
-40 -20
0 20 40 60 80
Temperature (ºC)
Note (3) 1 time for ± X, ± Y, ± Z. for Condition (200G / 2ms) is half Sine Wave,
Note (4) 10 ~ 200 Hz, 0.5 Hr / Cycle, 1 cycles for each X, Y, Z.
Note (5) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough
so that the module would not be twisted or bent by the fixture.
The fixing condition is shown as below:
Side Mount Fixing Screw
gap=2mm
LCD Module
Bracket
Side Mount Fixing Screw
Stage
5 / 28
Version 1.1
Datasheet pdf - http://www.DataSheet4U.co.kr/
5 Page Doc. No.: 44082127
Issued Date: Apr. 23, 2008
Model No.: N154Z3 - L01
Preliminary
inverter please make sure that a poor lighting caused by the mismatch of the Backlight and the
inverter (miss-lighting, flicker, etc.) never occurs. If the above situation is confirmed, the module
should be operated in the same manners when it is installed in your instrument.
The output of the inverter must have symmetrical (negative and positive) voltage waveform and
symmetrical current waveform.(Unsymmetrical ratio is less than 10%) Please do not use the inverter,
which has unsymmetrical voltage and unsymmetrical current and spike wave. Lamp frequency may
produce interface with horizontal synchronous frequency and as a result this may cause beat on the
display. Therefore lamp frequency shall be as away possible from the horizontal synchronous
frequency and from its harmonics in order to prevent interference.
Requirements for a system inverter design, which is intended to have a better display performance, a
better power efficiency and a more reliable lamp. It shall help increase the lamp lifetime and reduce its
leakage current.
a. The asymmetry rate of the inverter waveform should be 10% below;
b. The distortion rate of the waveform should be within 2 ± 10%;
c. The ideal sine wave form shall be symmetric in positive and negative polarities.
* Asymmetry rate:
www.DataSheet.net/
I p | I p – I –p | / Irms * 100%
I -p * Distortion rate
I p (or I –p) / Irms
11 / 28
Version 1.1
Datasheet pdf - http://www.DataSheet4U.co.kr/
11 Page |
Páginas | Total 28 Páginas | |
PDF Descargar | [ Datasheet N154Z3-L01.PDF ] |
Número de pieza | Descripción | Fabricantes |
N154Z3-L01 | TFT LCD Module | CMI MEI |
N154Z3-L02 | TFT LCD Module | CMI MEI |
N154Z3-L03 | TFT LCD Module | CMI MEI |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |