DataSheet26.com

HIP0082AB PDF даташит

Спецификация HIP0082AB изготовлена ​​​​«Intersil Corporation» и имеет функцию, называемую «Quad Power Drivers with Serial Diagnostic Interface».

Детали детали

Номер произв HIP0082AB
Описание Quad Power Drivers with Serial Diagnostic Interface
Производители Intersil Corporation
логотип Intersil Corporation логотип 

12 Pages
scroll

No Preview Available !

HIP0082AB Даташит, Описание, Даташиты
HIP0082, HIP0084
PRELIMINARY
May 1998
Quad Power Drivers with
Serial Diagnostic Interface
Features
• Low Side Power MOSFET Output Drivers
- Output Voltage Clamp (Typ) . . . . . . . . . . . . . . . . 80V
- Maximum Output Current . . . . . . . . . . . . . . . . 5A/2A
- Output rDS(ON) (TJ = 150oC) (Max) . . . . . 0.57/0.62
• Controlled Slew Rate Switching (HIP0084)
• Single Pulse Energy Rating . . . . . . . . . . . . . . . . . 70mJ
• Programmable Output Over Current Shutdown Threshold
- Bit Select 2A or 5A on Outputs 3 and 4
• Output Protection
- Output Over Current Shutdown
- Output Over Voltage Clamp
- Over Temperature Diagnostic Feedback
• Diagnostics for Shorts, Opens and Over Temperature
• Synchronous Serial Interface with
- 22-Bit Serial Diagnostic Register
- SPI Compatible Interface
• Single 5V Supply Operation with CMOS Logic Inputs
• Supply Current, ICC, Full Load (Typ) . . . . . . . . . <10mA
Low θJC Power SIP Packages
SIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3oC/W
PSOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2oC/W
• -40oC to 125oC Operating Temperature
Applications
• Drivers For
- Solenoids
- Relays
- Power Output
- Lamps
- Injectors
- Steppers
- Motors
- Displays
• System Use
- Automotive
- Appliances
- Industrial
- Robotics
Description
The HIP0082 and HIP0084 Quad Power Drivers contain four
individually protected NDMOS transistor switches to drive
inductive and resistive loads such as: fuel injectors, relays,
solenoids, etc. The outputs are low-side switches driven by
active-low CMOS logic inputs. Each output is protected
against excessive current due to a short-circuit. Internal
drain-to-gate zener diodes provide output clamping for over
voltage. An integrated charge pump allows operation from a
single 5V logic supply. Diagnostic circuits provide ground
short (SG), supply short (SC) and open load (OL) detection
for each of the four output stages and indicate over tempera-
ture. Diagnostic information may be read via a synchronous
serial interface. Six bits of write/store data sets a long or
short OL fault delay time for each output and sets Outputs 3
and 4 to a 2A or 5A current shutdown threshold. The
HIP0084 is specified with controlled slew rate switching.
Both types are fabricated in a Power BiMOS IC process and
are intended for use in automotive and other applications with a
wide range of temperature and electrical stress. They are par-
ticularly suited for driving high-current inductive loads requiring
high breakdown voltage and high output current. Both types
available in the 15 lead Power SIP or 20 lead PSOP packages
with low thermal resistance for high power applications.
Ordering Information
PART
NUMBER
HIP0082AS1
HIP0084AS1
HIP0082AS2
HIP0082AB
HIP0084AB
TEMP.
RANGE(°C)
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
PACKAGE
15 Ld SIP
15 Ld SIP
15 Ld SIP
20 Ld PSOP
20 Ld PSOP
PKG.
NO.
Z15.05A
Z15.05A
Z15.05B
M20.433
M20.433
Pinouts
HIP0082, HIP0084 (SIP)
TOP VIEW
HEAT SINK TAB INTERNALLY CONNECTED
TO PIN 8 GROUND (VSS)
15 IN3
14 OUT3
13 IN1
12 OUT1
11 R/W
10 VCC
9 RST
8 GND (VSS)
7 TXD
6 CLK
5 CS
4 OUT2
3 IN2
2 OUT4
1 IN4
HIP0082, HIP0084 (PSOP W/HEAT SLUG)
TOP VIEW
INTEGRAL COPPER
HEAT SINK ‘SLUG’
FOR PCB CONTACT
OR EXT. HEAT SINK
GND (SLUG)
IN4
OUT4
IN2
GND (VSS)
OUT2
CS
CLK
TXD
GND (SLUG)
1
2
3
4
5
6
7
8
9
10
20 GND (SLUG)
19 IN3
18 OUT3
17 IN1
16 GND (VSS)
15 OUT1
14 R/W
13 VCC
12 RST
11 GND (SLUG)
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
1
File Number 3643.4









No Preview Available !

HIP0082AB Даташит, Описание, Даташиты
HIP0082, HIP0084
Block Diagram
1 OF 4
CHANNELS
VCC
(NOTE 1) ROL
DOL
VBATT
VCC
INx
SQ
R
RST
POR
QOL
OSC
CHARGE
PUMP
QO
OL SG
VCC
RST
TXD
CLK
CS
R/W
VCC
POR
RESET
POR
RST
OSC
OVER
TEMP.
R/W
SHIFT
REG.
DIAG.
REG.
WRITE/
STORE
DELAY
SC
(SHORT CIRCUIT)
ISC REF (PROG. 3, 4)
FILTER
FILTER/
DELAY
OPEN-
LOAD
CURRENT
SENSE
-
OL+
IOL(MAX)
REF
-
OL
+
IOLF
REF
- (SHORT-TO-GND)
SG+ VSG
REF
OUTx
VSS
(GND)
HIP0084 OUTPUT STAGE
QO
OL SG
SC
VCC
NOTE 2,
CASE 1
VBATT
OUTx
NOTE 2,
CASE 2
NOTES:
1. For Open-Load Detection, the HIP0082 has an internal series pullup resistor, ROL and diode, DOL connected from OUTx to VCC.
2. HIP0084 OL (Open-Load) Detection:
Case 1: For OL Detection, an external series resistor and diode pullup connected from OUTx to VCC is needed.
Case 2: If no failure distinction for OL or SG (Short-to-GND) is required, both faults may be detected (without distinction), with an external
pulldown resistor.
For either case, the pullup or pulldown resistors should be typically 10kor greater.
2









No Preview Available !

HIP0082AB Даташит, Описание, Даташиты
HIP0082, HIP0084
Absolute Maximum Ratings TA = 25oC
Supply Voltage (Logic and Control), VCC . . . . . . . . . . . . -0.3V to 7V
Power MOSFET Drain Voltage, VO (Note 3) . . . . . . -0.7 to VCLAMP
Output Clamp Energy, EOK (See Note 5). . . . . . . . . . . . . . . . . 70mJ
Input Voltage (Logic and Driver Inputs), VIN. . . .-0.5V to VCC +0.5V
Maximum Output Current, Outputs 1 and 2 . . . . . . . . . . . . . . . . +2A
Maximum Output Current, Outputs 3 and 4 . . . . . . . . . . . . . . . . +5A
Maximum Total Output Current, All Outputs ON. . . . . . . . . . . . . +8A
Maximum Peak Output Current, IO(MAX), (Note 4) . . . . . -5A to ISC
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 125oC
Thermal Information
Thermal Resistance (Typical, Notes 5, 6, 7) θJA (oC/W) θJC (oC/W)
Power SIP Package . . . . . . . . . . . . . . .
45
3
PSOP Package . . . . . . . . . . . . . . . . . .
40
2
Maximum Junction Temperature . . . . . . . . . . . . . . . -40oC to 150oC
Maximum Storage Temperature Range, TSTG . . . . -55oC to 150oC
Maximum Lead Temperature (During Soldering 10s) . . . . . . 300oC
(PSOP - Lead Tips Only)
Die Characteristics
Back Side Potential . . . . . . . . . . . . . . . . . . . . . . . .VSS (Tab Ground)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
3. The MOSFET Output Drain is internally clamped with a Drain-to-Gate zener diode that turns on the MOSFET to hold the Drain at the
VCLAMP voltage. Refer to the Electrical Specifications Table for the VCLAMP voltage limits.
4. Each Output has Over Current Shutdown protection in the positive current direction. The maximum peak current rating is set equal to the
minimum Over Current Shutdown as detailed in the Electrical Specification Table. In the event of an Over Current Shutdown the input
drive is latched OFF. The output short must be removed and the input toggled OFF and ON to restore the output drive.
5. Refer to Application Note AN9416 for Single Pulse Energy and Device Dissipation rating information, including inductive load operation
and other thermal stress characterization.
6. θJA is measured with the component mounted on an evaluation PC board in free air.
7. Maximum PSOP Package Dissipation at 125oC with 26oC/W Heat Sink (6 sq cm Copper PCB) is 0.96W.
Electrical Specifications VCC = 5V ±10%, TA = -40oC to 125oC; Unless Otherwise Specified
HIP0082
HIP0084
PARAMETER
SYMBOL
TEST CONDITIONS
MIN TYP MAX MIN TYP MAX UNITS
POWER OUTPUTS
Output ON Resistance
(Normal Mode)
Output ON Resistance
(Normal Mode)
Output ON Resistance
(Normal Mode)
Output Zener Clamp Voltage
Matching Zener Clamp
Voltage
rDS(ON)1,
rDS(ON)2
Outputs 1 and 2, One Output ON,
IOUT = 2A, TJ = 150oC
rDS(ON)3, Outputs 3 and 4, One Output ON,
rDS(ON)4 IOUT = 2A, TJ = 150oC
rDS(ON)1,
rDS(ON)2
Outputs 1 and 2, One Output ON,
IOUT = 2A, TJ = 75oC
rDS(ON)3,
rDS(ON)4
Outputs 3 and 4, One Output ON,
IOUT = 2A, TJ = 105oC
VZ IOUT = 40mA
VZ IOUT = 40mA, tZ = 100µs
-
-
73
- 0.62 -
- 0.57 -
-
N/A
-
80 90 73
N/A -
- 0.62
- 0.57
- 0.5
- 0.5
80 90
- ±1.5
V
V
Output Short Current Limit,
Outputs 1 and 2 (Note 8)
ISC(L)
2 - 3.4 3 - 5.1 A
Output Short Current Limit,
Outputs 3 and 4 (Note 8)
ISC(L) ISC Bit High
2 - 3.4 2 - 3.4 A
Output Short Current Limit,
Outputs 3 and 4 (Note 8)
ISC(H) ISC Bit Low
5 - 7.5 5 - 8.3 A
Short Circuit Current Filter
Time
tSC
- - 1 - - 3 µs
Output Capacitance
CO VOUTX = 16V, f = 1MHz
- - 250 - - 250 pF
3










Скачать PDF:

[ HIP0082AB.PDF Даташит ]

Номер в каталогеОписаниеПроизводители
HIP0082ABQuad Power Drivers with Serial Diagnostic InterfaceIntersil Corporation
Intersil Corporation
HIP0082AS1Quad Power Drivers with Serial Diagnostic InterfaceIntersil Corporation
Intersil Corporation
HIP0082AS2Quad Power Drivers with Serial Diagnostic InterfaceIntersil Corporation
Intersil Corporation

Номер в каталоге Описание Производители
TL431

100 мА, регулируемый прецизионный шунтирующий регулятор

Unisonic Technologies
Unisonic Technologies
IRF840

8 А, 500 В, N-канальный МОП-транзистор

Vishay
Vishay
LM317

Линейный стабилизатор напряжения, 1,5 А

STMicroelectronics
STMicroelectronics

DataSheet26.com    |    2020    |

  Контакты    |    Поиск