|
|
Número de pieza | HIP1011B | |
Descripción | PCI Hot Plug Controller | |
Fabricantes | Intersil Corporation | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de HIP1011B (archivo pdf) en la parte inferior de esta página. Total 9 Páginas | ||
No Preview Available ! Data Sheet
HIP1011B
March 2000 File Number 4640.3
PCI Hot Plug Controller
The HIP1011B, the third product in the HIP1011 family, is an
electronic circuit breaker that monitors, reports and protects
circuits from excessive load currents. As a pin-for-pin drop-in
alternative offering similar functionality to the widely used
HIP1011, the HIP1011B is compatible with CompactPCI
peripheral boards and PCI Hot Plug systems where voltage
“health” monitoring and reporting are centralized by the
system controller IC. The HIP1011B does not monitor nor
respond to under voltage conditions thus making control of a
wide range of voltages possible.
The HIP1011B creates a small and simple yet complete
power control solution to control the four independent
supplies (+5V, +3.3V, +12V, and -12V) found in PCI and
CompactPCI systems. For the +12V and -12V supplies,
overcurrent protection is provided internally with integrated
current sensing FET switches. For the +5V and +3.3V
supplies, overcurrent protection is provided by sensing the
voltage across the external current-sense resistors. The
PWRON input controls the state of both internal and external
switches. During an overcurrent condition on any output, all
MOSFETs are latched-off and a LOW (0V) is asserted on
the FLTN output. The FLTN latch is cleared when the
PWRON input is toggled low again. During initial power-up of
the main VCC supply (+12V), the PWRON input is inhibited
from turning on the switches, and the latch is held in the
Reset state until the VCC input is greater than 10V.
User programmability of the overcurrent threshold, response
time and turn-on slew rate is provided. A resistor connected
to the OCSET pin programs the overcurrent thresholds. A
capacitor may be added to the FLTN pin to adjust the fault
reporting and power-supply latch-off response times after an
over-current event. Capacitors connected to the gate pins
determine the turn-on rate.
Ordering Information
PART NUMBER
HIP1011BCB
HIP1011BCB-T
TEMP. RANGE
(oC)
PACKAGE
0 to 70 16 Ld SOIC
0 to 70 Tape and Reel
PKG.
NO.
M16.15
Features
• Allows for System Centralized Voltage Monitoring
• Adjustable Delay to Fault Notification and Latch-Off
• Controls Four Supplies: +5V, +3.3V, +12V, and -12V
• Internal MOSFET Switches for +12V and -12V Outputs
• µP Interface for On/Off Control and Fault Reporting
• Adjustable Overcurrent Protection for All Supplies
• Provides Overcurrent Fault Isolation
• Adjustable Turn-On Slew Rate
• Minimum Parts Count Solution
• No Charge Pump
Applications
• PCI Hot Plug
• CompactPCI
Pinout
HIP1011B
(SOIC)
TOP VIEW
M12VIN 1
FLTN 2
3V5VG 3
VCC 4
12VIN 5
3VISEN 6
3VS 7
OCSET 8
16 M12VO
15 M12VG
14 12VG
13 GND
12 12VO
11 5VISEN
10 5VS
9 PWRON
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 2000
1 page HIP1011B
Electrical Specifications
PARAMETER
Nominal 5V and 3.3V Input Supply Voltages,
VCC = 12VIN = 12V, M12VIN = -12V, TA = TJ = 0 to 70oC, Unless Otherwise Specified (Continued)
SYMBOL
TEST CONDITIONS
MIN TYP MAX UNITS
+12V SUPPLY CONTROL
On Resistance of Internal PMOS
Overcurrent Threshold
Overcurrent Threshold
Gate Charge Current
Turn-On Time (PWRON High to
12VG = 1V)
rDS(ON)12
IOC12V_1
IOC12V_2
IC12VG
tON12V
PWRON = High, ID = 0.5A, TA = TJ = 25oC
VOCSET = 0.6V
VOCSET = 1.2V
PWRON = High, V12VG = 3V
C12VG = 0.022µF
0.18 0.3 0.35
0.6 0.75 0.9
1.25 1.50
1.8
22.5 25 28.5
- 16 20
Ω
A
A
µA
ms
Turn-Off Time
Turn-Off Time
-12V SUPPLY CONTROL
On Resistance of Internal NMOS
Overcurrent Threshold
Overcurrent Threshold
Gate Output Charge Current
Turn-On Time (PWRON High to
M12VG = -1V)
tOFF12V
C12VG = 0.1µF, 12VG
C12VG = 0.022µF, 12VG Rising 10% - 90%
rDS(ON)M12
IOC12V_1
IOC12V_2
ICM12VG
tONM12V
PWRON = High, ID = 0.1A, TA = TJ = 25oC
VOCSET = 0.6V
VOCSET = 1.2V
PWRON = High, V3VG = -4V
CM12VG = 0.022µF
- 9 12 µs
- 3 - µs
0.5 0.7 0.9
0.15 0.18 0.25
0.30 0.37 0.50
22.5 25 28.5
- 160 300
Ω
A
A
µA
µs
Turn-On Time (PWRON High to
tONM12V CM12VG = 0.022µF, CM12VO = 50µF, RL = 120Ω
-
16
-
ms
M12VO = -10.8V)
Turn-Off Time
Turn-Off Time
M12VIN Input Bias Current
CONTROL I/O PINS
tOFFM12V
IBM12VIN
CM12VG = 0.1µF, M12VG
CM12VG = 0.022µF, M12VG Falling 90% to 10%
PWRON = High
-
-
-
18 23 µs
3 - µs
2 2.6 mA
Supply Current
OCSET Current
Overcurrent Fault Response Time
PWRON Threshold Voltage
FLTN Output Low Voltage
FLTN Output High Voltage
FLTN Output Latch Threshold
12V Power On Reset Threshold
IVCC
IOCSET
tOC
VTHPWRON
VFLTN,OL
VFLTN,OH
VFLTN,TH
VPOR,TH
IFLTN = 2mA
IFLTN = 0 to -4mA
VCC Voltage Falling
4 5 5.8
95 100 105
- 500 960
0.8 1.6 2.1
- 0.6 0.9
3.9 4.3 4.9
1.45 1.8 2.25
8.7 9.4 9.9
mA
µA
ns
V
V
V
V
V
5
5 Page |
Páginas | Total 9 Páginas | |
PDF Descargar | [ Datasheet HIP1011B.PDF ] |
Número de pieza | Descripción | Fabricantes |
HIP1011 | PCI Hot Plug Controller | Intersil Corporation |
HIP1011A | PCI Hot Plug Controller | Intersil Corporation |
HIP1011B | PCI Hot Plug Controller | Intersil Corporation |
HIP1011D | Dual PCI Hot Plug Controller | Intersil Corporation |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |