DataSheet26.com

HCS190MS PDF даташит

Спецификация HCS190MS изготовлена ​​​​«Intersil Corporation» и имеет функцию, называемую «Radiation Hardened Synchronous 4-Bit Up/Down Counter».

Детали детали

Номер произв HCS190MS
Описание Radiation Hardened Synchronous 4-Bit Up/Down Counter
Производители Intersil Corporation
логотип Intersil Corporation логотип 

9 Pages
scroll

No Preview Available !

HCS190MS Даташит, Описание, Даташиты
HCS190MS
September 1995
Radiation Hardened Synchronous
4-Bit Up/Down Counter
Features
• 3 Micron Radiation Hardened SOS CMOS
• Total Dose 200K RAD (Si)
• SEP Effective LET No Upsets: >100 MEV-cm2/mg
• Single Event Upset (SEU) Immunity < 2 x 10-9 Errors/Bit-Day
(Typ)
• Dose Rate Survivability: >1 x 1012 RAD (Si)/s
• Dose Rate Upset >1010 RAD (Si)/s 20ns Pulse
• Latch-Up Free Under Any Conditions
• Military Temperature Range: -55oC to +125oC
• Significant Power Reduction Compared to LSTTL ICs
• DC Operating Voltage Range: 4.5V to 5.5V
• Input Logic Levels
- VIL = 30% of VCC Max
- VIH = 70% of VCC Min
• Input Current Levels Ii 5µA at VOL, VOH
Description
The Intersil HCS190MS is an asynchronously presettable BCD
Decade synchronous counter. Presetting the counter to the
number on the preset data inputs (P0 - P3) is accomplished by a
low on the parallel load input (PL). Counting occurs when (PL) is
high, Count Enable (CE) is low and the Up/Down (U/D) input is
either low for up-counting or high for down-counting. The counter
is incremented or decremented synchronously with the low-to-high
transition of the clock.
When an overflow or underflow of the counter occurs, the Terminal
Count output (TC), which is low during counting, goes high and
remains high for one clock cycle. This output can be used for look-
ahead carry in high speed cascading. The TC output also initiates
the Ripple Clock output (RC) which, normally high, goes low and
remains low for the low-level portion of the clock pulse. These
counter can be cascaded using the Ripple Carry output.
If the decade counter is preset to an illegal state or assumes an
illegal state when power is applied, it will return to the normal
sequence in one or two counts.
The HCS190MS utilizes advanced CMOS/SOS technology to
achieve high-speed operation. This device is a member of
radiation hardened, high-speed, CMOS/SOS Logic Family.
The HCS190MS is supplied in a 16 lead Ceramic flatpack
(K suffix) or a SBDIP Package (D suffix).
Pinouts
16 LEAD CERAMIC DUAL-IN-LINE
METAL SEAL PACKAGE (SBDIP)
MIL-STD-1835 CDIP2-T16
TOP VIEW
P1 1
Q1 2
Q0 3
CE 4
U/D 5
Q2 6
Q3 7
GND 8
16 VCC
15 P0
14 CP
13 RC
12 TC
11 PL
10 P2
9 P3
P1
Q1
Q0
CE
U/D
Q2
Q3
GND
16 LEAD CERAMIC METAL SEAL
FLATPACK PACKAGE (FLATPACK)
MIL-STD-1835 CDFP4-F16
TOP VIEW
1 16
2 15
3 14
4 13
5 12
6 11
7 10
89
VCC
P0
CP
RC
TC
PL
P2
P3
TRUTH TABLE
INPUTS
PL CE U/D CP
OUTPUT
FUNCTION
HL L
Count Up
HLH
Count Down
L X X X Preset
H H X X No Change
H = High Voltage Level
L = Low Voltage Level
X = Immaterial
=Positive Transistion
Ordering Information
PART NUMBER
HCS190DMSR
HCS190KMSR
HCS190D/Sample
HCS190K/Sample
HCS190HMSR
TEMPERATURE RANGE
-55oC to +125oC
-55oC to +125oC
+25oC
+25oC
+25oC
SCREENING LEVEL
Intersil Class S Equivalent
Intersil Class S Equivalent
Sample
Sample
Die
PACKAGE
16 Lead SBDIP
16 Lead Ceramic Flatpack
16 Lead SBDIP
16 Lead Ceramic Flatpack
Die
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999
260
Spec Number 518836
File Number 2251.2









No Preview Available !

HCS190MS Даташит, Описание, Даташиты
Specifications HCS190MS
Absolute Maximum Ratings
Reliability Information
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +7.0V
Input Voltage Range, All Inputs . . . . . . . . . . . . .-0.5V to VCC +0.5V
DC Input Current, Any One Input . . . . . . . . . . . . . . . . . . . . . . . .±10mA
DC Drain Current, Any One Output. . . . . . . . . . . . . . . . . . . . . . .±25mA
Storage Temperature Range (TSTG) . . . . . . . . . . . -65oC to +150oC
Lead Temperature (Soldering 10sec) . . . . . . . . . . . . . . . . . . +265oC
Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC
ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1
(All Voltage Reference to the VSS Terminal)
Thermal Resistance
θJA θJC
SBDIP Package. . . . . . . . . . . . . . . . . . . . 73oC/W 24oC/W
Ceramic Flatpack Package . . . . . . . . . . . 114oC/W 29oC/W
Maximum Package Power Dissipation at +125oC Ambient
SBDIP Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.68W
Ceramic Flatpack Package . . . . . . . . . . . . . . . . . . . . . . . . . 0.44W
If device power exceeds package dissipation capability, provide heat
sinking or derate linearly at the following rate:
SBDIP Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.7mW/oC
Ceramic Flatpack Package . . . . . . . . . . . . . . . . . . . . . . 8.8mW/oC
Gate Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Gates
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Operating Conditions
Operating Voltage Range . . . . . . . . . . . . . . . . . . . . . +4.5V to +5.5V
Input Rise and Fall Time at 4.5V VCC (tr, tf) . . . . . . . 100ns/V Max.
Operating Temperature Range . . . . . . . . . . . . . . . . -55oC to +125oC
Input High Voltage. . . . . . . . . . . . . . . . . . . . . . . VCC to 70% of VCC
Input Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . .0V to 30% of VCC
TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS
PARAMETER
Supply Current
SYMBOL
(NOTE 1)
CONDITIONS
ICC VCC = 5.5V,
VIN = VCC or GND
Output Current
(Source)
Output Current
(Sink)
Output Voltage High
Output Voltage Low
Input Leakage
Current
IOH
IOL
VOH
VOL
IIN
VCC = 4.5V, VIH = 4.5V,
VOUT = VCC -0.4V,
VIL = 0V, (Note 2)
VCC = 4.5V, VIH = 4.5V,
VOUT = 0.4V, VIL = 0V,
(Note 2)
VCC = 5.5V, VIH = 3.85V,
VIL = 1.65V, IOH = -50µA
VCC = 4.5V, VIH = 3.15V,
VIL = 1.35V, IOH = -50µA
VCC = 5.5V, VIH = 3.85V,
VIL = 1.65V, IOL = 50µA
VCC = 4.5V, VIH = 3.15V,
VIL = 1.35V, IOL = 50µA
VCC = 5.5V, VIN = VCC or
GND
Noise Immunity
Functional Test
FN VCC = 4.5V,
VIH = 3.15V,
VIL = 1.35V, (Note 3)
GROUP
A SUB-
GROUPS
1
2, 3
1
2, 3
1
2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1
2, 3
7, 8A, 8B
TEMPERATURE
+25oC
+125oC, -55oC
+25oC
+125oC, -55oC
+25oC
+125oC, -55oC
+25oC, +125oC, -55oC
+25oC, +125oC, -55oC
+25oC, +125oC, -55oC
+25oC, +125oC, -55oC
+25oC
+125oC, -55oC
+25oC, +125oC, -55oC
LIMITS
MIN MAX UNITS
- 40 µA
- 750 µA
-4.8 - mA
-4.0 - mA
4.8 - mA
4.0 - mA
VCC
-0.1
-
V
VCC
-0.1
-
V
- 0.1 V
- 0.1 V
- ±0.5 µA
- ±5.0 µA
- -V
NOTES:
1. All voltages reference to device GND.
2. Force/Measure functions may be interchanged.
3. For functional tests, VO 4.0V is recognized as a logic “1”, and VO 0.5V is recognized as a logic “0”.
Spec Number 518836
261









No Preview Available !

HCS190MS Даташит, Описание, Даташиты
Specifications HCS190MS
TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS
PARAMETER
Propagation Delay
PL to Qn
Pn to Qn
CP to Qn
CP to RC
CP to TC
U/D to RC
U/D to TC
CE to RC
SYMBOL
(NOTES 1, 2)
CONDITIONS
TPLH
VCC = 4.5V, VIH = 4.5V,
VIL = 0V
TPHL
VCC = 4.5V, VIH = 4.5V,
VIL = 0V
TPLH
VCC = 4.5V, VIH = 4.5V,
VIL = 0V
TPHL
VCC = 4.5V, VIH = 4.5V,
VIL = 0V
TPLH
VCC = 4.5V, VIH = 4.5V,
VIL = 0V
TPHL
VCC = 4.5V, VIH = 4.5V,
VIL = 0V
TPLH
VCC = 4.5V, VIH = 4.5V,
VIL = 0V
TPHL
VCC = 4.5V, VIH = 4.5V,
VIL = 0V
TPLH
VCC = 4.5V, VIH = 4.5V,
VIL = 0V
TPHL
VCC = 4.5V, VIH = 4.5V,
VIL = 0V
TPLH
VCC = 4.5V, VIH = 4.5V,
VIL = 0V
TPHL
VCC = 4.5V, VIH = 4.5V,
VIL = 0V
TPLH
VCC = 4.5V, VIH = 4.5V,
VIL = 0V
TPHL
VCC = 4.5V, VIH = 4.5V,
VIL = 0V
TPLH
VCC = 4.5V, VIH = 4.5V,
VIL = 0V
TPHL
VCC = 4.5V, VIH = 4.5V,
VIL = 0V
GROUP
A SUB-
GROUPS
9
10, 11
9
10, 11
9
10, 11
9
10, 11
9
10, 11
9
10, 11
9
10, 11
9
10, 11
9
10, 11
9
10, 11
9
10, 11
9
10, 11
9
10, 11
9
10, 11
9
10, 11
9
10, 11
TEMPERATURE
+25oC
+125oC, -55oC
+25oC
+125oC, -55oC
+25oC
+125oC, -55oC
+25oC
+125oC, -55oC
+25oC
+125oC, -55oC
+25oC
+125oC, -55oC
+25oC
+125oC, -55oC
+25oC
+125oC, -55oC
+25oC
+125oC, -55oC
+25oC
+125oC, -55oC
+25oC
+125oC, -55oC
+25oC
+125oC, -55oC
+25oC
+125oC, -55oC
+25oC
+125oC, -55oC
+25oC
+125oC, -55oC
+25oC
+125oC, -55oC
NOTES:
1. All voltages referenced to device GND.
2. AC measurements assume RL = 500, CL = 50pF, Input TR = TF = 3ns.
LIMITS
MIN MAX UNITS
2 30 ns
2 35 ns
2 35 ns
2 41 ns
2 28 ns
2 33 ns
2 33 ns
2 38 ns
2 31 ns
2 37 ns
2 28 ns
2 34 ns
2 25 ns
2 28 ns
2 24 ns
2 26 ns
2 41 ns
2 49 ns
2 40 ns
2 47 ns
2 37 ns
2 40 ns
2 34 ns
2 40 ns
2 40 ns
2 43 ns
2 40 ns
2 36 ns
2 24 ns
2 25 ns
2 26 ns
2 26 ns
Spec Number 518836
262










Скачать PDF:

[ HCS190MS.PDF Даташит ]

Номер в каталогеОписаниеПроизводители
HCS190MSRadiation Hardened Synchronous 4-Bit Up/Down CounterIntersil Corporation
Intersil Corporation

Номер в каталоге Описание Производители
TL431

100 мА, регулируемый прецизионный шунтирующий регулятор

Unisonic Technologies
Unisonic Technologies
IRF840

8 А, 500 В, N-канальный МОП-транзистор

Vishay
Vishay
LM317

Линейный стабилизатор напряжения, 1,5 А

STMicroelectronics
STMicroelectronics

DataSheet26.com    |    2020    |

  Контакты    |    Поиск