|
|
PDF ALR-1400 Data sheet ( Hoja de datos )
| Número de pieza | ALR-1400 | |
| Descripción | DVI INTERFACE CONTROLLER | |
| Fabricantes | Digital View | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de ALR-1400 (archivo pdf) en la parte inferior de esta página. Total 25 Páginas | ||
|
No Preview Available !
PC, DVI INTERFACE CONTROLLER
FOR TFT PANEL
Model: ALR-1400
Part number : 41710002X-3
INSTRUCTIONS
CONTENTS
Page: 2. Introduction, How to Proceed, Usage Note, Disclaimer
2. System design – Diagram of a suggested system
3. Assembly notes – Important information about system elements
5. Connection & Operation – How to use the controller
8. Connectors, pinouts & jumpers – Essential connection information
14. Controller dimensions
15. Application notes
18. Troubleshooting
19. Specifications
20. Appendix I – Graphic Mode Support Table
21. Appendix II – RS-232 control protocols
22. Appendix III – Mapping definition
24. Warranty, Caution & Limitation of Liability, Trademarks
25. Contact details
It is essential that these instructions are read and understood before connecting or
powering up this controller.
1
1 page  
CONNECTION & OPERATION
CAUTION: Never connect or disconnect parts of the display system when the system is powered up as this may cause serious
damage.
CONNECTION
Connection and usage is quite straight forward (it is useful to have the relevant connection diagram available at this time):
1. LCD panel & Inverter: Connect the inverter (if it is not built-in the panel) to the CCFT lead connector of the LCD
panel.
2. LVDS type panels: Plug the LVDS signal cable direct to CN1 (if necessary). Insert the panel end of the cable to the
LCD panel connector.
3. TTL type panels: Plug the signal cables direct to CN2 or CN3. Plug the other end of cables to the LCD connector
board (if connector board is required, otherwise the signal can be direct plug to the LCD panel
connector). Then plug the board connector to the LCD panel connector.
4. Inverter & Controller: Plug the inverter cable to CNB1 and CNA1 (if necessary). Plug another end to the connector
on the inverter.
5. Function switch & Controller: Plug the OSD switch mount cable to CNC1 on the controller board and another to
the OSD switch mount.
6. LED & Controller: Plug in a 3-way with dual colour LED to connector LED1 on the controller board.
7. Jumpers : Check all jumpers are set correctly. Details referring the connection diagram at
http://www.digitalview.com/controllers/csg.php
8. Jumpers & Inverter & Panel voltage: Particularly pay attention to the settings of JA3, JB2, JB3, JA5. JB2 & JB3
are used for inverter control (read inverter specification and information on the jumper table to define the correct
settings). JA3 & JA5 are used for panel voltage input (read panel specification and information on the jumper table to
define the correct settings).
9. DVI cable : Plug the DVI cable to the connector P2 on the controller board.
10. VGA cable & Controller: Plug the VGA cable to the connector P1 on the controller board.
11. Power supply & Controller: Plug the DC 12V power in to the connector PP2. You can consider to use DigitalView
mating power cable P/N 426013800-3, 160mm.
12. Power on: Switch on the controller board and panel by using the OSD switch mount.
CAUTION: Never connect or disconnect parts of the display system when the system is powered up as this may cause serious
damage.
LED status :
State
No signal & backlight off
No signal & backlight on
With signal & backlight on
LED color
RED
ORANGE
GREEN
General:
• If you are using supplied cables & accessories, ensure they are correct for the model of panel and controller.
• If you are making your own cables & connectors refer carefully to both the panel & inverter specifications and the section
in this manual, “Connectors, Pinouts & Jumpers” to ensure the correct pin to pin wiring.
PC SETTINGS
The controller has been designed to take a very wide range of input signals however to optimize the PC’s graphics performance
we recommend choosing 60Hz vertical refresh rate – this will not cause screen flicker.
OPERATION
Once the system has been connected and switched on there are a number of functions available to adjust the display
image as summarized in the following sections. The settings chosen will be saved for each mode independently.
5
5 Page 
28 NC
29 EB0
30 EB1
31 EB2
32 EB3
33 EB4
34 EB5
35 EB6
36 EB7
37 GND
38 GND
39 CLK
40 NC
No connection
Even data bit B0
Even data bit B1
Even data bit B2
Even data bit B3
Even data bit B4
Even data bit B5
Even data bit B6
Even data bit B7
Ground
Ground
Dot clock
No connection
CN3 – Panel connector: HIROSE DF20G-50DP-1V (Matching type : DF20A-50DS-1C)
PIN SYMBOL
DESCRIPTION
1 GND
Ground
2 GND
Ground
3 NC
No connection
4 NC
No connection
5 OR0
Odd data bit R0
6 OR1
Odd data bit R1
7 OR2
Odd data bit R2
8 OR3
Odd data bit R3
9 OR4
Odd data bit R4
10 OR5
Odd data bit R5
11 OR6
Odd data bit R6
12 OR7
Odd data bit R7
13 GND
Ground
14 GND
Ground
15 NC
No connection
16 NC
No connection
17 OG0
Odd data bit G0
18 OG1
Odd data bit G1
19 OG2
Odd data bit G2
20 OG3
Odd data bit G3
21 OG4
Odd data bit G4
22 OG5
Odd data bit G5
23 OG6
Odd data bit G6
24 OG7
Odd data bit G7
25 GND
Ground
26 GND
Ground
27 NC
No connection
28 NC
No connection
29 OB0
Odd data bit B0
30 OB1
Odd data bit B1
31 OB2
Odd data bit B2
32 OB3
Odd data bit B3
33 OB4
Odd data bit B4
34 OB5
Odd data bit B5
35 OB6
Odd data bit B6
36 OB7
Odd data bit B7
37 GND
Ground
38 GND
Ground
39 VS
Vertical sync
40 CLK
Dot clock
41 HS
Horizontal sync
42 DE
Display enable
43 PWR
Power down control signal (5v TTL)
44 VLCD
Panel power supply (3.3v/5v configurable)
45 VLCD
Panel power supply (3.3V/5v configurable)
46 VLCD
Panel power supply (3.3V/5v configurable)
47 NC
No connection
48 VLCD12
+12V panel supply (selected by JA5)
49 VLCD12
+12V panel supply (selected by JA5)
50 VLCD12
+12V panel supply (selected by JA5)
11
11 Page | ||
| Páginas | Total 25 Páginas | |
| PDF Descargar | [ Datasheet ALR-1400.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| ALR-1400 | DVI INTERFACE CONTROLLER | Digital View |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |