HB288192A5 Datasheet PDF - Hitachi Semiconductor
| Part Number | HB288192A5 | |
| Description | FLASH ATA Card | |
| Manufacturers | Hitachi Semiconductor | |
| Logo |  |
|
|
There is a preview and HB288192A5 download ( pdf file ) link at the bottom of this page. Total 30 Pages | ||
Preview 1 page No Preview Available !
HB288800A5/HB288640A5
HB288448A5/HB288320A5
HB288256A5/HB288192A5
HB288160A5/HB288128A5
HB288096A5/HB288064A5
HB288032A5
FLASH ATA Card
800 MByte/640 MByte/448 MByte/320 MByte
256 MByte/192 MByte/160 MByte/128 MByte
96 MByte/64 MByte/32 MByte
ADE-203-952D (Z)
Rev. 3.0
Oct. 2, 2000
Description
HB288800A5, HB288640A5, HB288448A5, HB288320A5, HB288256A5, HB288192A5, HB288160A5,
HB288128A5, HB288096A5, HB288064A5, HB288032A5 are Flash ATA card. This card complies with PC
card ATA standard and is suitable for the usage of data storage memory medium for PC or any other electric
equipment. This card is equipped with Hitachi 256 Mega bit Flash memory. This card is suitable for ISA
(Industry Standard Architecture) bus interface standard , and read/write unit is 1 sector (512 bytes) sequential
access. By using this card it is possible to operate good performance for the system which have PC card slots.
Features
• PC card ATA standard specification
68 pin two pieces connector and Type II (5 mm)
• 3.3 V/5 V single power supply operation
• ISA standard and Read/Write unit is 512 bytes (sector) sequential access
Sector Read/Write transfer rate: 8MB/sec burst
|
| |
 
HB288800/640/448/320/256/192/160/128/096/064/032A5
Card Pin Explanation
Signal name
Direction Pin No.
Description
A10 to A0
I
(PC Card Memory mode)
8, 11, 12, 22, 23, Address bus is A10 to A0. A10 is MSB and A0 is
24, 25, 26, 27, LSB.
28, 29
A10 to A0
(PC Card I/O mode)
A2 to A0
(True IDE mode)
27, 28, 29
Address bus is A10 to A0. Only A2 to A0 are used,
A10 to A3 should be grounded by the host.
BVD1
I/O
(PC Card Memory mode)
63
BVD1 outputs the battery voltage status in the card.
This output line is constantly driven to a high state
since a battery is not required for this product.
-STSCHG
(PC Card I/O mode)
-STSCHG is used for changing the status of
Configuration and status register in attribute area.
-PDIAG
(True IDE mode)
-PDIAG is the Pass Diagnostic signal in Master/Slave
handshake protocol.
BVD2
I/O
(PC Card Memory mode)
62
BVD2 outputs the battery voltage status in the card.
This output line is constantly driven to a high state
since a battery is not required for this product.
-SPKR
(PC Card I/O mode)
-SPKR outputs speaker signals. This output line is
constantly driven to a high state since this product
does not support the audio function.
-DASP
(True IDE mode)
-DASP is the Disk Active/Slave Present signal in the
Master/Slave handshake protocol.
-CD1, -CD2
O
(PC Card Memory mode)
36, 67
-CD1 and -CD2 are the card detection signals. -CD1
and -CD2 are connected to ground in this card, so
host can detect that the card is inserted or not.
-CD1, -CD2
(PC Card I/O mode)
-CD1, -CD2
(True IDE mode)
-CE1, -CE2
I
(PC Card Memory mode)
Card Enable
7, 42
-CE1 and -CE2 are low active card select signals.
Byte/Word/Odd byte mode are defined by combination
of -CE1, -CE2 and A0.
-CE1, -CE2
(PC Card I/O mode)
Card Enable
-CE1, -CE2
(True IDE mode)
-CE2 is used for select the Alternate Status Register
and the Device Control Register while -CE1 is the chip
select for the other task file registers.
5
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for HB288192A5 electronic component. |
| Information | Total 30 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ HB288192A5.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| HB288192A5 | The function is FLASH ATA Card. Hitachi Semiconductor | |
| HB288192A6 | The function is FLASH ATA Card. Hitachi Semiconductor | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
HB28
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||