DataSheet26.com

HC-5504 PDF даташит

Спецификация HC-5504 изготовлена ​​​​«Intersil Corporation» и имеет функцию, называемую «ITU Low Cost/ PABX SLIC With 40mA Loop Feed».

Детали детали

Номер произв HC-5504
Описание ITU Low Cost/ PABX SLIC With 40mA Loop Feed
Производители Intersil Corporation
логотип Intersil Corporation логотип 

9 Pages
scroll

No Preview Available !

HC-5504 Даташит, Описание, Даташиты
Data Sheet
HC-5504B
July 1998 File Number 2886.5
EIA/ITU PABX SLIC with 40mA Loop Feed
The Intersil SLIC incorporates many of the BORSHT functions
on a single IC chip. This includes DC battery feed, a ring relay
driver, supervisory and hybrid functions. This device is
designed to maintain transmission performance in the
presence of externally induced longitudinal currents. Using
the unique Intersil dielectric isolation process, the SLIC can
operate directly with a wide range of station battery voltages.
The SLIC also provides selective denial of power. If the PBX
system becomes overloaded during an emergency, the SLIC
will provide system protection by denying power to selected
subscriber loops.
The Intersil SLIC is ideally suited for the design of new digital
PBX systems by eliminating bulky hybrid transformers.
Ordering Information
PART
NUMBER
HC1-5504B-5
HC1-5504B-9
HC3-5504B-5
HC3-5504B-9
HC4P5504B-5
HC4P5504B-9
HC9P5504B-5
HC9P5504B-9
TEMP. RANGE
(oC)
PACKAGE
0 to 75
24 Ld CERDIP
-40 to 85 24 Ld CERDIP
0 to 75
24 Ld PDIP
-40 to 85 24 Ld PDIP
0 to 75
28 Ld PLCC
-40 to 85 28 Ld PLCC
0 to 75
24 Ld SOIC
-40 to 85 24 Ld SOIC
PKG. NO.
F24.6
F24.6
E24.6
E24.6
N28.45
N28.45
M24.3
M24.3
Pinouts
HC-5504B (PDIP, CERDIP, SOIC)
TOP VIEW
TIP 1
RING 2
RFS 3
VB+ 4
C3 5
DG 6
RS 7
RD 8
TF 9
RF 10
VB- 11
BG 12
24 TX
23 AG
22 C4
21 RX
20 +IN
19 -IN
18 OUT
17 C2
16 RC
15 PD
14 GKD
13 SHD
Features
• Pin for Pin Replacement for the HC-5504
• Capable of 5V or 12V (VB+) Operation
• Monolithic Integrated Device
• DI High Voltage Process
• Compatible With Worldwide PBX Performance
Requirements
• Controlled Supply of Battery Feed Current for Short Loops
(41mA)
• Internal Ring Relay Driver
• Allows Interfacing With Negative Superimposed Ringing
Systems
• Low Power Consumption During Standby
• Switch Hook Ground Key and Ring Trip Detection
Functions
• Selective Denial of Power to Subscriber Loops
Applications
• Solid State Line Interface Circuit for Analog and
Digital PBX Systems
• Direct Inward Dial (DID) Trunks
• Voice Messaging PBXs
• Related Literature
- AN549, The HC-5502S/4X Telephone Subscriber Line
Interface Circuits (SLIC)
- AN571, Using Ring Sync with HC-5502A and HC-5504
SLICs
HC-5504B (PLCC)
TOP VIEW
4 3 2 1 28 27 26
VB+ 5
C3 6
DG 7
N/C 8
RS 9
RD 10
TF 11
25 RX
24 +IN
23 -IN
22 N/C
21 OUT
20 C2
19 RC
12 13 14 15 16 17 18
51 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999









No Preview Available !

HC-5504 Даташит, Описание, Даташиты
HC-5504B
Absolute Maximum Ratings (Note 1)
Maximum Continuous Supply Voltages
(VB-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -60V to 0.5V
(VB+) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 15V
(VB+ - VB-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75V
Relay Drive Voltage (VRD) . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 15V
Operating Conditions
Operating Temperature Range
HC-5504B-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 75oC
HC-5504B-9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC
Relay Driver Voltage (VRD) . . . . . . . . . . . . . . . . . . . . . . . . . 5 to 12V
Positive Supply Voltage (VB+) . . . . . . . 4.75 to 5.25 or 10.8 to 13.2V
Negative Supply Voltage (VB-). . . . . . . . . . . . . . . . . . . . . -42 to -58V
High Level Logic Input Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . 2.4V
Low Level Logic Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . 0.6V
Loop Resistance (RL) . . . . . . . . . . . . . . . . . . . . . . . . . 200 to 1200
Thermal Information
Thermal Resistance (Typical, Note 2)
θJA (oC/W)
CERDIP Package. . . . . . . . . . . . . . . . . . . . . . . . . . .
52
PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
65
PLCC Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
65
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
75
Maximum Junction Temperature (Hermetic Packages) . . . . . .175oC
Maximum Junction Temperature (Plastic Packages) . . . . . . . .150oC
Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . .300oC
(PLCC and SOIC - Lead Tips Only)
Die Characteristics
Transistor Count. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
Diode Count. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Die Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 x 102
Substrate Potential. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connected
Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bipolar-DI
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Absolute maximum ratings are limiting values, applied individually, beyond which the serviceability of the circuit may be impaired.
Functional operability under any of these conditions is not necessarily implied.
2. θJA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications
UTAnl=es2s5OoCth. eMrwini-sMeaSxpPeacirfiaemde, tVeBrs-
= -48V, VB+ = 12V and 5V, AG =
are Over Operating Temperature
BG = DG
Range
=
0V,
Typical
Parameters
PARAMETER
CONDITIONS
MIN TYP MAX UNITS
On Hook Power Dissipation
Off Hook Power Dissipation
Off Hook IB+
Off Hook IB+
Off Hook IB-
Off Hook Loop Current
Off Hook Loop Current
Off Hook Loop Current
Fault Currents
TIP to Ground
ILONG = 0 (Note 3), VB+ = 12V
RL = 600, ILONG = 0 (Note 3), VB+ = 12V
RL = 600, ILONG = 0 (Note 3), TA = -40oC
RL = 600, ILONG = 0 (Note 3), TA = 25oC
RL = 600, ILONG = 0 (Note 3)
RL = 1200, ILONG = 0 (Note 3)
RL = 1200, VB- = -42V, ILONG = 0 (Note 3)
TA = 25oC
RL = 200, ILONG = 0 (Note 3)
- 170 235 mW
- 425 550 mW
- - 6.0 mA
- - 5.3 mA
- 35 41 mA
- 21 - mA
17.5 -
- mA
36 41 48 mA
- 14 - mA
RING to Ground
- 55 - mA
TIP to RING
- 41 - mA
TIP and RING to Ground
- 55 - mA
Ring Relay Drive VOL
Ring Relay Driver Off Leakage
Ring Trip Detection Period
IOL = 62mA
VRD = 12V, RC = 1 = HIGH, TA = 25oC
RL = 600
- 0.2 0.5 V
- - 100 µA
- 2 3 Ring
Cycles
Switch Hook Detection Threshold
SHD = VOL
SHD = VOH
10 -
--
- mA
5 mA
52









No Preview Available !

HC-5504 Даташит, Описание, Даташиты
HC-5504B
Electrical Specifications
UTAnl=es2s5OoCth. eMrwini-sMeaSxpPeacirfiaemde, tVeBrs-
= -48V, VB+ = 12V and 5V, AG =
are Over Operating Temperature
BG = DG = 0V, Typical
Range (Continued)
Parameters
PARAMETER
CONDITIONS
MIN TYP MAX UNITS
Ground Key Detection Threshold
Loop Current During Power Denial
Dial Pulse Distortion
GKD = VOL
GKD = VOH
RL = 200
20 -
- mA
- - 10 mA
- ±2 - mA
0 - 5 ms
Receive Input Impedance
Transmit Output Impedance
2-Wire Return Loss
SRL LO
ERL
SRL HI
Longitudinal Balance
2-Wire Off Hook
(Note 3)
(Note 3)
Referenced to 600+ 2.16µF (Note 3)
1VRMS 200Hz - 3400Hz (Note 3) IEEE Method
0oC TA 75oC
- 110 -
- 10 20
- 15.5 -
- 24 -
- 31 -
58 65
-
k
dB
dB
dB
dB
2-Wire On Hook
60 63 - dB
4-Wire Off Hook
50 58 - dB
Low Frequency Longitudinal Balance
R.E.A. Method (Note 3), RL = 600
0oC TA 75oC
- - 23 dBrnC
- - -67 dBm0p
Insertion Loss
2-Wire to 4-Wire, 4 Wire to 2-Wire
Frequency Response
at 1kHz, 0dBm Input Level, Referenced 600
200Hz - 3400Hz Referenced to Absolute Loss at
1kHz and 0dBm Signal Level (Note 3)
- ±0.05 ±0.2 dB
-
±0.02 ±0.05
dB
Idle Channel Noise
2-Wire to 4-Wire, 4 Wire to 2-Wire
(Note 3)
- 1 5 dBrnC
- -89 -85 dBm0p
Absolute Delay
2-Wire to 4-Wire, 4 Wire to 2-Wire
Trans Hybrid Loss
(Note 3)
- - 2 ms
Balance Network Set Up for 600Termination at
36
40
-
dB
1kHz
Overload Level
2-Wire to 4-Wire, 4 Wire to 2-Wire
Level Linearity
2-Wire to 4-Wire, 4 Wire to 2-Wire
VB+ = +5V
VB+ = 12V
At 1kHz Referenced to 0dBm Level (Note 3)
+3 to -40dBm
-40 to -50dBm
-50 to -55dBm
1.5
1.75
-
-
-
- - VPEAK
- - VPEAK
-
±0.05
dB
- ±0.1 dB
- ±0.3 dB
Power Supply Rejection Ratio
VB+ to 2-Wire
VB+ to Transmit
VB- to 2-Wire
VB- to Transmit
(Note 3)
30 - 60Hz, RL = 600
15 -
15 -
15 -
15 -
- dB
- dB
- dB
- dB
53










Скачать PDF:

[ HC-5504.PDF Даташит ]

Номер в каталогеОписаниеПроизводители
HC-5502BEIA/ITU PABX SLIC with 30mA Loop FeedIntersil Corporation
Intersil Corporation
HC-5502B1SLIC Subscriber Line Interface CircuitIntersil Corporation
Intersil Corporation
HC-5504EIA/ITU PABX SLIC with 40mA Loop FeedIntersil Corporation
Intersil Corporation
HC-5504ITU Low Cost/ PABX SLIC With 40mA Loop FeedIntersil Corporation
Intersil Corporation

Номер в каталоге Описание Производители
TL431

100 мА, регулируемый прецизионный шунтирующий регулятор

Unisonic Technologies
Unisonic Technologies
IRF840

8 А, 500 В, N-канальный МОП-транзистор

Vishay
Vishay
LM317

Линейный стабилизатор напряжения, 1,5 А

STMicroelectronics
STMicroelectronics

DataSheet26.com    |    2020    |

  Контакты    |    Поиск