|
|
Número de pieza | NCP1207 | |
Descripción | PWM Current-Mode Controller | |
Fabricantes | ON Semiconductor | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de NCP1207 (archivo pdf) en la parte inferior de esta página. Total 18 Páginas | ||
No Preview Available ! NCP1207
PWM Current−Mode
Controller for Free Running
Quasi−Resonant Operation
The NCP1207 combines a true current mode modulator and a
demagnetization detector to ensure full borderline/critical
Conduction Mode in any load/line conditions and minimum drain
voltage switching (Quasi−Resonant operation). Due to its inherent skip
cycle capability, the controller enters burst mode as soon as the power
demand falls below a predetermined level. As this happens at low peak
current, no audible noise can be heard. An internal 8.0 ms timer prevents
the free−run frequency to exceed 100 kHz (therefore below the 150 kHz
CISPR−22 EMI starting limit), while the skip adjustment capability lets
the user select the frequency at which the burst foldback takes place.
The Dynamic Self−Supply (DSS) drastically simplifies the
transformer design in avoiding the use of an auxiliary winding to supply
the NCP1207. This feature is particularly useful in applications where
the output voltage varies during operation (e.g. battery chargers). Due to
its high−voltage technology, the IC is directly connected to the
high−voltage DC rail. As a result, the short−circuit trip point is not
dependent upon any VCC auxiliary level.
The transformer core reset detection is done through an auxiliary
winding which, brought via a dedicated pin, also enables fast
Overvoltage Protection (OVP). Once an OVP has been detected, the IC
permanently latches off.
Finally, the continuous feedback signal monitoring implemented with
an Overcurrent Fault Protection (OCP) circuitry makes the final design
rugged and reliable.
Features
• Pb−Free Packages are Available*
• Free−Running Borderline/Critical Mode Quasi−Resonant Operation
• Current−Mode with Adjustable Skip−Cycle Capability
• No Auxiliary Winding VCC Operation
• Auto−Recovery Overcurrent Protection
• Latching Overvoltage Protection
• External Latch Triggering, e.g. Via Overtemperature Signal
• 500 mA Peak Current Source/Sink Capability
• Internal 1.0 ms Soft−Start
• Internal 8.0 ms Minimum TOFF
• Adjustable Skip Level
• Internal Temperature Shutdown
• Direct Optocoupler Connection
• SPICE Models Available for TRANsient Analysis
Typical Applications
• AC−DC Adapters for Notebooks, etc.
• Offline Battery Chargers
• Consumer Electronics (DVD Players, Set−Top Boxes, TVs, etc.)
• Auxiliary Power Supplies (USB, Appliances, TVs, etc.)
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
© Semiconductor Components Industries, LLC, 2004
October, 2004 − Rev. 8
1
http://onsemi.com
8
1
8
1
SOIC−8
D1, D2 SUFFIX
CASE 751
MARKING
DIAGRAMS
8
1207
ALYW
1
PDIP−8
N SUFFIX
CASE 626
8
1
1207P
AWL
YYWW
1207/P = Device Code
A = Assembly Location
WL, L = Wafer Lot
YY, Y = Year
WW, W = Work Week
PIN CONNECTIONS
DMG 1
FB 2
CS 3
GND 4
8 HV
7 NC
6 VCC
5 Drv
(Top View)
ORDERING INFORMATION
Device
Package
Shipping†
NCP1207DR2
SOIC−8 2500/Tape & Reel
NCP1207DR2G SOIC−8 2500/Tape & Reel
(Pb−Free)
NCP1207P
PDIP−8
50 Units/Tube
NCP1207PG
PDIP−8
(Pb−Free)
50 Units/Tube
†For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specifications
Brochure, BRD8011/D.
Publication Order Number:
NCP1207/D
1 page NCP1207
TYPICAL CHARACTERISTICS
(TJ = −40°C to 125°C)
13.2
7 12.8
12.4
12.0
11.6
11.2
10.8
11.2
10.8
10.4
10.0
9.6
9.2
10.4
−50 −25
0
25 50 75 100 125
TEMPERATURE (°C)
Figure 3. VCC Increasing Level at which the
Current Source Turns−off versus Temperature
1.60
1.40
8.8
−50
−25
0
25 50 75 100 125
TEMPERATURE (°C)
Figure 4. VCC Decreasing Level at which the
Current Source Turns−on versus Temperature
2.30
2.10
1.20 1.90
1.00 1.70
0.80 1.50
0.60 1.30
0.40
−50 −25 0 25 50 75 100 125
TEMPERATURE (°C)
Figure 5. Internal IC Consumption, No Output
Load on Pin 5 versus Temperature
12
11
10
9
8
7
6
5
4
3
2
−50 −25
0 25 50 75
TEMPERATURE (°C)
100 125
Figure 7. Internal Startup Current Source,
VCC = 10 V versus Temperature
1.10
−50
−25
0 25 50 75
TEMPERATURE (°C)
100 125
Figure 6. Internal IC Consumption, Output
Load on Pin 5 versus Temperature
1.20
1.15
1.10
1.05
1.00
0.95
0.90
−50
−25
0 25 50 75
TEMPERATURE (°C)
100 125
Figure 8. Maximum Internal Current Setpoint
versus Temperature
http://onsemi.com
5
5 Page NCP1207
Demagnetization Detection
The core reset detection is done by monitoring the voltage
activity on the auxiliary winding. This voltage features a
FLYBACK polarity. The typical detection level is fixed at
50 mV as exemplified by Figure 21.
7.0
400
300
200
5.0 POSSIBLE
RESTARTS
3.0
100
0
1.0
0V
−1.0
50 mV
Figure 21. Core reset detection is done through a
dedicated auxiliary winding monitoring
TO INTERNAL
COMPARATOR
Resd
2
1
1
Rdem
5
4
Rint
ESD2
ESD1
Aux
Resd + Rint = 28 k
43
Figure 22. Internal Pad Implementation
An internal timer prevents any restart within 8.0 ms further
to the driver going−low transition. This prevents the
switching frequency to exceed (1 / (TON + 8.0 ms)) but also
avoid false leakage inductance tripping at turn−off. In some
cases, the leakage inductance kick is so energetic, that a
slight filtering is necessary.
The 1207 demagnetization detection pad features a
specific component arrangement as detailed by Figure 22. In
this picture, the zener diodes network protect the IC against
any potential ESD discharge that could appear on the pins.
The first ESD diode connected to the pad, exhibits a parasitic
capacitance. When this parasitic capacitance (10 pF
typically) is combined with Rdem, a restart delay is created
and the possibility to switch right in the drain−source wave
exists. This guarantees QR operation with all the associated
benefits (low EMI, no turn−on losses etc.). Rdem should be
calculated to limit the maximum current flowing through
pin 1 to less than +3 mA/−2 mA. If during turn−on, the
auxiliary winding delivers 30 V (at the highest line level),
then the minimum Rdem value is defined by:
(30 V + 0.7 V) / 2 mA = 14.6 kW.
This value will be further increased to introduce a restart
delay and also a slight filtering in case of high leakage
energy.
Figure 23 portrays a typical VDS shot at nominal output
power.
Figure 23. The NCP1207 Operates in
Borderline / Critical Operation
Overvoltage Protection
The overvoltage protection works by sampling the plateau
voltage 4.5 ms after the turn−off sequence. This delay
guarantees a clean plateau, providing that the leakage
inductance ringing has been fully damped. If this would not
be the case, the designer should install a small RC damper
across the transformer primary inductance connections.
Figure 24 shows where the sampling occurs on the auxiliary
winding.
SAMPLING HERE
8.0
6.0
4.0
2.0
4.5 ms
0
Figure 24. A voltage sample is taken 4.5 ms after
the turn−off sequence
When an OVP condition has been detected, the NCP1207
enters a latchoff phase and stops all switching operations.
The controller stays fully latched in this position and the
DSS is still active, keeping the VCC between 5.3 V/12 V as
in normal operations. This state lasts until the VCC is cycled
down 4 V, e.g. when the user unplugs the power supply from
the mains outlet.
By default, the OVP comparator is biased to a 5 V
reference level and pin 1 is routed via a divide by 1.44
network. As a result, when Vpin1 reaches 7.2 V, the OVP
comparator is triggered. The threshold can thus be adjusted
by either modifying the power winding to auxiliary winding
turn ratios to match this 7.2 V level, or insert a resistor from
pin1 to ground to cope with your design requirement.
http://onsemi.com
11
11 Page |
Páginas | Total 18 Páginas | |
PDF Descargar | [ Datasheet NCP1207.PDF ] |
Número de pieza | Descripción | Fabricantes |
NCP120 | Very Low Dropout Bias Rail CMOS Voltage Regulator | ON Semiconductor |
NCP1200 | PWM Current-Mode Controller for Low-Power Universal Off-Line Supplies | ON Semiconductor |
NCP1200A | PWM Current-Mode Controller for Universal Off-Line Supplies Featuring Low Standby Power | ON |
NCP1200AP100 | PWM Current-Mode Controller for Universal Off-Line Supplies Featuring Low Standby Power | ON Semiconductor |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |