DataSheet26.com

WD1003-RAH PDF даташит

Спецификация WD1003-RAH изготовлена ​​​​«Western Digital» и имеет функцию, называемую «Disk Controllers User Guide».

Детали детали

Номер произв WD1003-RAH
Описание Disk Controllers User Guide
Производители Western Digital
логотип Western Digital логотип 

14 Pages
scroll

No Preview Available !

WD1003-RAH Даташит, Описание, Даташиты
USER'S GUIDE
WD 1003-RAH
WD 1003S-RAH
WD 1003-RA2
WD 1003A-RA2
Winchester
Disk Controllers
Important Information
Do not Discard









No Preview Available !

WD1003-RAH Даташит, Описание, Даташиты
Document Scope
This document describes the hardware and software installation of the following Western
Digital controllers:
WD 1003-RAH
WD1003S-RAH
WD 1003-RA2
WD 1003A-RA2
Two versions of the WD1003-RA2 are available:
Feature 000 (F000). Non-translation operation only
Feature 001 (F00l). Translation operation only.
The other controllers described in this document have one standard version.
These controllers are designed for use in IBM Personal Computer ATs or other AT-compatible
computers with a 16-bit data bus.
The use of the term controller refers to all boards described within this document. When a
reference is made to a particular board, the appropriate WD part number is used.









No Preview Available !

WD1003-RAH Даташит, Описание, Даташиты
JUMPER
W1
W2
W3
W4
W5
W6
WDl003-RAH JUMPER SETTINGS
PIN CONNECTS
DESCRIPTION
1-2
OPEN
Standard factory setting. Status read is latched. Used for IBM
Personal Computer AT if Winchester activity LED is connected to
J6.
Status read is not latched. Activity LED turns on during drive
access. W5 must be jumpered 2 to 3. Used for Compaq hosts.
OPEN
1-2
Standard factory setting. Selects primary addresses, 1F0 through
1F7 and 3F0 through 3F7 hex. Do not modify the primary address
jumper unless your BIOS operating system is configured to accept
more than two hard disk drives.
Selects secondary addresses, 170 through 177 and 370 through
377 hex.
OPEN
1-2
This configuration used with WD11C00C-22 at board location US
or if W5 is jumpered 1 to 2. Required only on early units with
WD11C00-22 at board location U8 and W5 is jumpered 1 to 2. DO
NOT JUMPER WITH THE WDl1C00C-22 INSTALLED.
2-3 Standard factory setting. No translation for drive 0.
1-2 Enables translation for drive 0. Translation is only available for
615 cylinders and four headed drives. In translation mode, the
controller translates the 26 physical sectors per track into 17
sectors. The extra sectors are "translated" into logical heads. To
use the translation mode, select through the Setup program a 615
cylinder and six head drive type. (This is drive type three for IBM
Personal Computer AT users. Not all AT-compatible systems use
the same drive tables as IBM.) This configuration must be used
when running an operating system or application program which
requires a 17 sector per track disk drive.
2-3 Standard factory setting. WG and drive select lines only enabled
when drive is accessed. This configuration also provides power up
and down protection.
1-2 WG and drive select lines are disabled during power up reset and
when + 5V power supply drops below approximately +4.1 5V.
2-3 Standard factory setting. No translation for drive 1.
1-2 Enables translation for drive 1. Translation is only available for
615 cylinders and four headed drives. In translation mode, the
controller translates the 26 physical sectors per track into 17
sectors. The extra sectors are "translated" into logical heads. To
use the translation mode, select through the Setup program a 615
cylinder and six head drive type. (This is drive type three for IBM
Personal Computer AT users. Not all AT-compatible systems use
the same drive tables as IBM.) This configuration must be used
when running an operating system or application program which
requires a 17 sector per track disk drive.










Скачать PDF:

[ WD1003-RAH.PDF Даташит ]

Номер в каталогеОписаниеПроизводители
WD1003-RA2Disk Controllers User GuideWestern Digital
Western Digital
WD1003-RAHDisk Controllers User GuideWestern Digital
Western Digital

Номер в каталоге Описание Производители
TL431

100 мА, регулируемый прецизионный шунтирующий регулятор

Unisonic Technologies
Unisonic Technologies
IRF840

8 А, 500 В, N-канальный МОП-транзистор

Vishay
Vishay
LM317

Линейный стабилизатор напряжения, 1,5 А

STMicroelectronics
STMicroelectronics

DataSheet26.com    |    2020    |

  Контакты    |    Поиск