DataSheet26.com

HCD-GTZ5 PDF даташит

Спецификация HCD-GTZ5 изготовлена ​​​​«Sony» и имеет функцию, называемую «COMPACT DISC RECEIVER SERVICE MANUAL».

Детали детали

Номер произв HCD-GTZ5
Описание COMPACT DISC RECEIVER SERVICE MANUAL
Производители Sony
логотип Sony логотип 

30 Pages
scroll

No Preview Available !

HCD-GTZ5 Даташит, Описание, Даташиты
http://www.xiaoyu163.com
HCD-GTZ4/GTZ4i/GTZ5QQSE3RV7IC6E3M1AN5U1AL50
892498299
US Model
Ver. 1.1 2009.08
AEP Model
Australian Model
HCD-GTZ4i
E Model
HCD-GTZ4/GTZ5
• HCD-GTZ4 is the amplier, USB, Disc player, tuner and
iPod section in MHC-GTZ4.
• HCD-GTZ4i is the amplier, USB, Disc player, tuner and
iPod section in LBT-GTZ4i, MHC-GTZ4i.
• HCD-GTZ5 is the amplier, USB, Disc player, tuner and
iPod section in MHC-GTZ5.
Photo: HCD-GTZ5
“WALKMAN” and “WALKMAN”
logo are registered trademarks of
Sony Corporation.
MICROVAULT is a trademark of
Sony Corporation.
Model Name Using Similar Mechanism
Mechanism Type
Optical Pick-up Block Name
NEW
CDM88B-DVBU101
KHM-313CAB
MPEG Layer-3 audio coding technol-
SPECIFICATIONS
ogy and patents licensed from Fraun-
hofer IIS and Thomson.
AUDIO POWER SPECIFICATION
Inputs
Windows Media is a registered trade-
mark of Microsoft Corporation in the
TEL 13942296513 QQ 376315150United States and/or other countries.
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
(HCD-GTZ4i: US model only)
With 6 ohm loads, both channels driven, from
120 Hz – 10 kHz; rated 110 watts per channel minimum RMS
PC (AUDIO IN) L/R:
Voltage 700 mV
impedance 47 kilohms
MIC: sensitivity 1 mV, impedance 10 kilohms
(USB) port: Type A
“Memory Stick” is a trademark of
Sony Corporation.
iPod is a trademark of Apple Inc., reg-
istered in the U.S. and other countries.
power, with no more than 0.7% total harmonic distortion from
250 miliwatts to rated output.
Amplifier section
HCD-GTZ5
The following are measured at
Mexican model:
AC 127 V, 60 Hz
Other models:
AC 120, 220, 240 V, 50/60 Hz
Outputs
PHONES: accepts headphones of 8 : or more
FRONT SPEAKER: accepts impedance of 6 :
SUBWOOFER: accepts impedance of 6 :
USB section
Supported bit rate
MP3 (MPEG 1 Audio Layer-3):
32 – 320 kbps, VBR
WMA: 48 – 192 kbps
AAC: 48 – 320 kbps
Front speaker
Sampling frequencies
Power output (rated): 110 W + 110 W
MP3 (MPEG 1 Audio Layer-3):
(at 6 :, 1 kHz, 1% THD)
32/44.1/48 kHz
RMS output power (reference):
WMA: 44.1 kHz
200 W + 200 W (per channel at 6 :, 1 kHz, 10% THD)
AAC: 44.1 kHz
Subwoofer
Transfer speed
RMS output power (reference): 200 W
(at 6 :, 100 Hz, 10% THD)
Full-Speed
Supported USB device
HCD-GTZ4i (US model)
Mass Storage Class
Maximum current
The following are measured at AC 120 V 60 Hz
Front speaker
RMS output power (reference):
:: SHUFKDQQHODWŸN+]7+'
Subwoofer
RMS output power (reference): 180 W
DWŸ+]7+'
500 mA
Disc player section
System
Compact disc and digital audio system
Laser Diode Properties
Emission Duration: Continuous
Laser Output*: Less than 44.6 PW
HCD-GTZ4 / GTZ4i
(AEP, Australian, Argentina models)
The following are measured at
European model:
AC 230 V, 50 Hz
Other models:
AC 120, 220, 240 V, 50/60 Hz
Front speaker
Power output (rated): 90 W + 90 W
(at 6 :, 1 kHz, 1% THD)
RMS output power (reference):
155 W + 155 W (per channel at 6 :, 1 kHz, 10% THD)
* This output is the value measurement at a distance of
200 mm from the objective lens surface on the Optical
Pick-up Block with 7 mm aperture.
Frequency response
20 Hz – 20 kHz
Signal-to-noise ratio
More than 90 dB
Dynamic range
More than 88 dB
Tuner section
FM stereo, FM/AM superheterodyne tuner
Subwoofer
RMS output power (reference): 150 W
(at 6 :, 100 Hz, 10% THD)
FM tuner section
Tuning range:
892498299North American model:
87.5 – 108.0 MHz (100 kHz step)
Other models:
87.5 – 108.0 MHz (50 kHz step)
Antenna: FM lead antenna
Antenna terminals: 75 ohms unbalanced
Intermediate frequency: 10.7 MHz
AM tuner section
Tuning range
Pan American and Oceanian models:
530 – 1,710 kHz (with 10 kHz tuning interval)
531 – 1,710 kHz (with 9 kHz tuning interval)
European models:
531 – 1,602 kHz (with 9 kHz tuning interval)
Other models:
530 – 1,610 kHz (with 10 kHz tuning interval)
531 – 1,602 kHz (with 9 kHz tuning interval)
Antenna: AM loop antenna, external antenna terminal
Intermediate frequency: 450 kHz
iPod section
DC5V 500mA MAX
General
Power requirements
North American model: AC 120 V, 60 Hz
European models: AC 230 V, 50/60 Hz
Oceanian model: AC 230 – 240 V, 50/60 Hz
Mexican model: AC 127 V, 60 Hz
Argentine model: AC 220 V, 50/60 Hz
Other models: AC 120, 220 or 230 – 240 V, 50/60 Hz,
Adjustable with voltage selector
Power consumption
MHC-GTZ5: 250 W
HCD-GTZ4i (American model): 240W
MHC-GTZ4 / GTZ4i (Other models): 300 W
Dimensions (w/h/d) (excl. speakers)
Approx. 231 × 361 × 430.5 mm
(9 1/8 × 14 1/4 × 17 1/4 inch)
Mass (excl. speakers)
HCD-GTZ5 / GTZ4 / GTZ4i:
10.0 kg (22 lb 1 oz)
Design and specifications are subject to change without notice.
‡6WDQGE\SRZHUFRQVXPSWLRQ:
‡+DORJHQDWHGIODPHUHWDUGDQWVDUHQRWXVHGLQWKHFHUWDLQ
printed wiring boards.
www x aoy u163 com. i9-889-503-02 Sony Corporation
COMPACT DISC RECEIVER
.
2009H05-1
Audio&Video Business Group
© 2009.08
Published by Sony Techno Create Corporation
http://www.xiaoyu163.com









No Preview Available !

HCD-GTZ5 Даташит, Описание, Даташиты
HCD-GTZ4/GTZ4i/GTZ5
Ver. 1.1
http://www.xiaoyu163.com
NOTES ON CHIP COMPONENT REPLACEMENT
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
QQ 376315150 892498299agedbyheat.
TABLE OF CONTENTS
1. SERVICING NOTES ............................................. 3
FLEXIBLE CIRCUIT BOARD REPAIRING
• Keep the temperature of soldering iron around 270 °C during
repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY CHECK-OUT
After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
2. DISASSEMBLY
2-1. Disassembly Flow...........................................................
2-2. Case (Side-L/R) ..............................................................
2-3. Top Case..........................................................................
2-4. Front Panel Block ...........................................................
2-5. DC Fan (M101)...............................................................
2-6. Back Panel ......................................................................
2-7. MAIN Board ...................................................................
2-8. DC Fan (M102), POWER AMP Board...........................
2-9. HUB Board, DMB19 Board ...........................................
2-10. CD Mechanism Block (CDM88B-DVBU101)...............
2-11. Optical Pick-up Block (KHM-313CAB) ........................
2-12. Belt (DLM3A) ................................................................
4
4
5
5
6
6
7
7
8
8
9
9
3. TEST MODE ............................................................ 10
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
TEL 13942296513scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2 V AC range are suitable. (See
Fig. A)
To Exposed Metal
Parts on Set
0.15 μF
1.5 kΩ
AC
voltmeter
(0.75 V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specied herein may result in hazardous radia-
tion exposure.
4. ELECTRICAL CHECK ......................................... 12
5. DIAGRAMS
5-1. Block Diagram - RF SERVO, USB Section -................. 13
5-2. Block Diagram - MAIN Section -................................... 14
5-3. Block Diagram - AMP Section - ..................................... 15
5-4. Block Diagram
- PANEL, POWER SUPPLY Section -........................... 16
5-5. Printed Wiring Board - DMB19 Board - ........................ 18
5-6. Schematic Diagram - DMB19 Board (1/3) - .................. 19
5-7. Schematic Diagram - DMB19 Board (2/3) - .................. 20
5-8. Schematic Diagram - DMB19 Board (3/3) - .................. 21
QQ 376315150 8924982995-9. Printed Wiring Board - MAIN Board -........................... 22
5-10. Schematic Diagram - MAIN Board (1/3) -..................... 23
5-11. Schematic Diagram - MAIN Board (2/3) -..................... 24
5-12. Schematic Diagram - MAIN Board (3/3) -..................... 25
5-13. Printed Wiring Board - HUB Board - ............................. 26
5-14. Schematic Diagram - HUB Board -................................ 27
5-15. Printed Wiring Board - POWER AMP Board - .............. 28
5-16. Schematic Diagram - POWER AMP Board - ................. 29
5-17. Printed Wiring Board - DISPLAY Board - ..................... 30
5-18. Schematic Diagram - DISPLAY Board - ........................ 31
5-19. Printed Wiring Boards - PANEL Section - ..................... 32
5-20. Schematic Diagram - PANEL Section -.......................... 33
5-21. Printed Wiring Board - TRANS Board -......................... 34
5-22. Schematic Diagram - TRANS Board - ........................... 35
6. EXPLODED VIEWS
6-1. Case Section.................................................................... 44
6-2. Loading Panel Section .................................................... 45
6-3. DISPLAY Board Section ................................................ 46
6-4. Front Panel Section......................................................... 47
6-5. Back Panel Section ......................................................... 48
6-6. MAIN Board Section ...................................................... 49
6-7. Chassis Section ............................................................... 50
6-8. CD Mechanism Section (CDM88B-DVBU101) ............ 51
7. ELECTRICAL PARTS LIST .............................. 52
Accessories are given in the last of the electrical parts list.
This appliance is classified as a CLASS 1
www . xiaoy u163. comLASERproduct.Thismarkingislocatedon
the rear exterior.
SAFETY-RELATED COMPONENT WARNING!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
2
http://www.xiaoyu163.com









No Preview Available !

HCD-GTZ5 Даташит, Описание, Даташиты
http://www.xiaoyu163.com
HCD-GTZ4/GTZ4i/GTZ5
SECTION 1
Ver. 1.1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP
QQ 376315150 892498299BLOCK OR BASE UNIT
MODEL IDENTIFICATION
– Back Panel –
The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The exible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
TEL 13942296513 QQCaution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
PART No.
Model
HCD-GTZ5: E2, E51
HCD-GTZ5: AR
HCD-GTZ5: MX
HCD-GTZ4: E2, E51
HCD-GTZ4: AR
HCD-GTZ4i: AUS
HCD-GTZ4i: AEP
HCD-GTZ4i: US
Part No.
4-124-494-0[]
4-124-494-1[]
4-124-494-3[]
4-131-035-0[]
4-131-035-1[]
4-131-035-6[]
4-131-035-7[]
4-131-035-8[]
• Abbreviation
AR : Argentina model
AUS : Australian model
376315150 892498299E2 : 120V AC area in E model
E51 : Chilean and Peruvian models
MX : Mexican model
HOW TO OPEN THE TRAY WHEN POWER SWITCH
TURN OFF
Note: Work after removing the case (side-R) referring to “2-2. CASE
(SIDE-L/R)” on disassembly (page 4).
NOTE OF REPLACING THE IC102 ON THE DMB19
BOARD
IC102 on the DMB19 board cannot exchange with single. When
this part is damaged, exchange the entire mounted board.
RELEASING THE DISC TRAY LOCK
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
Releasing Procedure:
1. Press [I/1 STANDBY] button to turn the power on.
2. Press the [CD] button to select CD function.
3. While pressing the [x] button, press the [Z OPEN/CLOSE]
button for more 5 seconds).
state of opening the CD tray
4. The message “UNLOCKED” is displayed and the disc tray is
unlocked.
lever
1 Turn a gear by
a driver till a lever
rises up to the
Note: When LOCKEDis displayed, the slot lock is not released by
position of the figure.
turning power on/off with the [I/1 STANDBY] button.
www x aoyu163 com. i
. gear
http://www.xiaoyu163.com
3










Скачать PDF:

[ HCD-GTZ5.PDF Даташит ]

Номер в каталогеОписаниеПроизводители
HCD-GTZ4COMPACT DISC RECEIVER SERVICE MANUALSony
Sony
HCD-GTZ4iCOMPACT DISC RECEIVER SERVICE MANUALSony
Sony
HCD-GTZ5COMPACT DISC RECEIVER SERVICE MANUALSony
Sony

Номер в каталоге Описание Производители
TL431

100 мА, регулируемый прецизионный шунтирующий регулятор

Unisonic Technologies
Unisonic Technologies
IRF840

8 А, 500 В, N-канальный МОП-транзистор

Vishay
Vishay
LM317

Линейный стабилизатор напряжения, 1,5 А

STMicroelectronics
STMicroelectronics

DataSheet26.com    |    2020    |

  Контакты    |    Поиск