DataSheet26.com

S110 PDF даташит

Спецификация S110 изготовлена ​​​​«Solid State Optronic» и имеет функцию, называемую «Relay».

Детали детали

Номер произв S110
Описание Relay
Производители Solid State Optronic
логотип Solid State Optronic логотип 

5 Pages
scroll

No Preview Available !

S110 Даташит, Описание, Даташиты
S110
1 Form A
Solid State Relay
DESCRIPTION
The S110 is a bi-directional, single-pole, single-throw, normally open multipurpose relay. The circuit is composed of one LED on the input
side which activates an optically coupled IC on the output - controlling the firing angle of two back-to-back SCRs. This circuit assures no
false triggering under most adverse conditions, and a tight zero-volt window not exceeding 5V.
FEATURES
Zero-Volt Cross Switching
High transient immunity
400V blocking voltage
0.8A maximum continuous current
High input-to-output isolation
Solid state reliability
OPTIONS/SUFFIXES*
-H High Input / Output isolation
-S Surface Mount Option
-TR Tape and Reel Option
NOTE: Suffixes listed above are not included in marking on
device for part number identification.
SCHEMATIC DIAGRAM
APPLICATIONS
Valve control
Solenoids
Home appliances
Metering equipment
Heating elements
ABSOLUTE MAXIMUM RATINGS*
PARAMETER
UNIT MIN TYP MAX
Storage Temperature
°C -55
125
Operating Temperature
°C -40
85
Continuous Input Current mA
40
Transient Input Current
mA
400
Reverse Input Control
Voltage
Output Power Dissipation
V
mW
6
800
*The values indicated are absolute stress ratings. Functional operation of the
device is not implied at these or any conditions in excess of those defined in
electrical characteristics section of this document. Exposure to Absolute
Ratings may cause permanent damage to the device and may adversely
affect reliability.
APPROVALS
UL/ C-L Approved File #E90096
BABT Approved #608203
© 2007 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Page 1 of 5
S110
rev 1.41 (10/23/2007)









No Preview Available !

S110 Даташит, Описание, Даташиты
S110
1 Form A
Solid State Relay
ELECTRICAL CHARACTERISTICS - 25°C
PARAMETER
UNIT MIN TYP MAX TEST CONDITIONS
INPUT SPECIFICATIONS
LED Forward Voltage
LED Reverse Voltage
Turn-On Crrent (Resistive Load)
TurnOn Curent (Inductive Load)
Junction Capacitance
OUTPUT SPECIFICATIONS
V
V
mA
mA
pF
1.2 1.5 If = 10mA
6 12
Ir = 10uA
5 6.5 Io = 0.8A
10 12 Io = 300uA (AC)
5 Vf = 0V
Blocking Voltage
V 400
Continuous Load Current
A
0.8 If = 6.5mA
Surge Current Rating
A
10 T = 16ms
Holding Current
mA
10
On-Voltage V 1.2 Io = 0.8A
Zero-Cross Turn-On Threshold Voltage V
5 If = 6.5mA
Leakage Current
Thermal Resistance
µA
° C/W
100 250 Vo = 250V
80
Power Factor
0.3 1
See Note 1 below
Critical Rate of Rise (dV/dt)
V/µs
400
COUPLED SPECIFICATIONS
Isolation Voltage
-H Suffix
Isolation Resistance
Coupled Capacitance
V 2500
V 3750
G 100
pF 6
T = 1 minute
T = 1 minute
Note 1: Snubber circuits may be requred for lower power factors
© 2007 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Page 2 of 5
S110
rev 1.41 (10/23/2007)









No Preview Available !

S110 Даташит, Описание, Даташиты
S110
1 Form A
Solid State Relay
PERFORMANCE DATA
S110
Maximum Load Current vs. Temperature
1000
800
600
400
200
0
Tem perature (C)
S110
Typical Blocking Voltage Distribution
N = 100, Ambient Temperature = 25°C
40
30
20
10
0
425 450 475 500 525 550 575 600
Blocking Voltage (V)
ZERO-VOLT SWITCHING
This solid state relay has been designed with a driver circuit that controls the operation of two back-to-back silicon controlled rectifiers
(SCRs), each responsible for one half of the AC cycle. If an AC signal is examined, the turn on, turn off and zero-volt switching can be seen.
Figure 1 shows a typical 60 Hz, 120Vac signal with a corresponding relay input signal:
1
Relay Input Signal is
Turned On.
5 Relay Input Signal is
Turned Off.
Input Signal
5V
Threshold
2
SCR #1 Turns On when
5V threshold is reached.
6 SCR #1 and Relay Turn
Off at Zero Volts.
3
SCR #1 Turns Off,
SCR #2 Turns On
at Zero Volts.
4
SCR #2 Turns Off,
SCR #1 Turns On
at Zero Volts.
Figure 1 shows the sequence of zero-volt switching operation. At Stage 1, an input signal is applied to the relay. The relay will not turn on
until the threshold voltage of 5V is reached. Once this point is reached (Stage 2), SCR #1 (designated as the SCR which controls positive
AC voltage) turns on. However, SCR #1 only conducts for an instant, as the cycle quickly crosses zero. At this point (Stage 3), SCR #1 will
turn off and SCR #2 (negative AC voltage) turns on. Likewise, at the next zero cross (Stage 4), SCR #2 will turn off and SCR #1 conducts
again. Even though the input signal is terminated at Stage 5, the relay will continue to conduct (typical SCR behavior) until Stage 6, when
SCR #1 crosses zero and ceases to conduct. Please note that turn on can likewise begin on the negative phase of the AC cycle with a -5V
threshold, though only the positive phase is shown here.
© 2007 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Page 3 of 5
S110
rev 1.41 (10/23/2007)










Скачать PDF:

[ S110.PDF Даташит ]

Номер в каталогеОписаниеПроизводители
S11THIN FILM SPST SWITCHTyco Electronics
Tyco Electronics
S110RelaySolid State Optronic
Solid State Optronic
S110-T11.0A SURFACE MOUNT SCHOTTKY BARRIER RECTIFIERWon-Top Electronics
Won-Top Electronics
S110-T31.0A SURFACE MOUNT SCHOTTKY BARRIER RECTIFIERWon-Top Electronics
Won-Top Electronics

Номер в каталоге Описание Производители
TL431

100 мА, регулируемый прецизионный шунтирующий регулятор

Unisonic Technologies
Unisonic Technologies
IRF840

8 А, 500 В, N-канальный МОП-транзистор

Vishay
Vishay
LM317

Линейный стабилизатор напряжения, 1,5 А

STMicroelectronics
STMicroelectronics

DataSheet26.com    |    2020    |

  Контакты    |    Поиск