|
|
Número de pieza | LQ104S1DG34 | |
Descripción | LCD Module | |
Fabricantes | Sharp | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de LQ104S1DG34 (archivo pdf) en la parte inferior de esta página. Total 17 Páginas | ||
No Preview Available ! 1 page LD21408B-3
4. Input Terminals
4-1. TFT-LCD panel driving
CN1 Employed connector: 9686S-40B-GF (IRISO)Terminal :Au plating 【Note 1】
Pin No.
1
Symbol
Function
Test1 TEST1(Please be sure to connect 1pin with ground)
2 GND Ground
3 CK Clock signal for sampling each data signal
4 GND Ground
5 Test2 TEST2(Please be sure to connect 5pin with ground)
6 Test3 TEST3 (Please be sure to open 6pin )
7 R0 RED data signal(LSB)
8 R1 RED data signal
9 R2 RED data signal
10 GND Ground
11 R3 RED data signal
12 R4 RED data signal
13 R5 RED data signal(MSB)
14 GND Ground
15 G0 GREEN data signal(LSB)
16 G1 GREEN data signal
17 G2 GREEN data signal
18 GND Ground
19 G3 GREEN data signal
20 G4 GREEN data signal
21 G5 GREEN data signal(MSB)
22 GND Ground
23 B0 BLUE data signal(LSB)
24 B1 BLUE data signal
25 B2 BLUE data signal
26 GND Ground
27 B3 BLUE data signal
28 B4 BLUE data signal
29 B5 BLUE data signal(MSB)
30 GND Ground
31 Test4 TEST4 (Please be sure to open 31pin )
32 GND Ground
33 Test5 TEST5 (Please be sure to open 33pin )
34 GND Ground
35 ENAB Data enable signal
36 NC No Connect
37 Vcc power supply (+3.3V)
38 Vcc power supply (+3.3V)
39 NC No Connect
40 Vcc power supply (+3.3V)
Remark
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
【Note 2】
-
-
-
-
-
【Note 1】Refer to the one that the size of FFC/FPC was recommended it of input connector.
The terminal of FFC/FPC of input connector recommend gold or gold plating specification.
Because point of contact with its is gold plating specification.
【Note 2】The horizontal and vertical display location is designated and controlled by rising timing
of ENAB signal. However if ENAB signal is fixed to “Low”, display is not able to display
correct image. ..See: 8-2
5 Page 10. Optical Characteristics
Parameter
Symbol Condition
Viewing Horizontal θ21, θ22 CR>10
angle Vertical
θ11
range
θ12
Contrast ratio
CR θ=0o
Optimum
viewing
angle
Response Rise
τr
time Decay τd θ=0o
Chromaticity of white
x
y
Luminance of white
White Uniformity
YL
δW
Min.
60
35
45
300
-
-
-
0.253
0.269
175
-
LD21408B-9
Ta=25oC, Vcc=+3.3V
Typ. Max. Unit
Remark
70 - Deg. [Note1]
50 - Deg. [Note4]
60 - Deg.
--
[Note2]
500 -
[Note4]
10
25
0.313
0.329
250
-
-
-
0.373
0.399
-
1.45
ms
ms
cd/m2
[Note3]
[Note4]
[Note4]
IF=18mA
[Note5]
[Note] The measurement shall be executed 30 minutes after lighting at rating.
The optical characteristics shall be measured in a dark room or equivalent state with
the method shown in Fig.3 below. (IF=18mA)
Photodetector
Viewing angle/Response time : BM-5A (TOPCON)
Contrast ratio/Luminance of white/Chromaticity : SR-3(TOPCON)
TFT-LCD module
Field=1°
400mm
LCD panel
Center of the screen
Fig.3 Optical characteristics measurement method
11 Page |
Páginas | Total 17 Páginas | |
PDF Descargar | [ Datasheet LQ104S1DG34.PDF ] |
Número de pieza | Descripción | Fabricantes |
LQ104S1DG31 | TFT LCD Module | Sharp |
LQ104S1DG34 | LCD Module | Sharp |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |