|
|
PDF AMS1585CM-15 Data sheet ( Hoja de datos )
| Número de pieza | AMS1585CM-15 | |
| Descripción | 4.6A LOW DROPOUT VOLTAGE REGULATOR | |
| Fabricantes | Advanced Monolithic Systems | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de AMS1585CM-15 (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
|
No Preview Available !
Advanced
Monolithic
Systems
AMS1585
4.6A LOW DROPOUT VOLTAGE REGULATOR
FEATURES
• Three Terminal Adjustable or Fixed Voltages
1.5V, 2.5V, 2.85V, 3.0V, 3.3V, 3.5V and 5.0V
• Output Current of 4.6A
• Operates Down to 1.35V Dropout
• Load Regulation: 0.1%
• Line Regulation: 0.015%
• TO-220 and TO-263 packages available
APPLICATIONS
• High Efficiency Linear Regulators
• Post Regulators for Switching Supplies
• Microprocessor Supply
• Battery Chargers
• Constant Current Regulators
• Notebook/Personal Computer Supplies
• Portable Instrumentation
GENERAL DESCRIPTION
TThhee AMS1585 series of adjustable and fixed voltage regulators are designed to provide 4.6A output current and to operate
down to 1.35V input-to-output differential at maximum output current, decreasing at lower load currents.
On-chip trimming adjusts the reference voltage to 1%. Current limit is also trimmed, minimizing the stress under overload
conditions on both the regulator and power source circuitry.
The AMS1585 devices are pin compatible with older three-terminal regulators and are offered in 3 lead TO-220 package and 3
lead TO-263 (Plastic DD).
ORDERING INFORMATION:
PACKAGE TYPE
3 Lead TO-220
3 Lead TO-263
AMS1585CT
AMS1585CT-1.5
AMS1585CT-2.5
AMS1585CT-2.85
AMS1585CT-3.0
AMS1585CT-3.3
AMS1585CT-3.5
AMS1585CT-5
AMS1585CM
AMS1585CM-1.5
AMS1585CM-2.5
AMS1585CM-2.85
AMS1585CM-3.0
AMS1585CM-3.3
AMS1585CM-3.5
AMS1585CM-5
PIN CONNECTIONS
OPERATING JUNCTION
TEMPERATURE RANGE
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
FIXED VERSION
1- Ground
2- VOUT
3- VIN
ADJUSTABLE VERSION
1- Adjust
2- VOUT
3- VIN
FRONT VIEW
TAB IS
OUTPUT
3
2
1
TAB IS
OUTPUT
FRONT VIEW
3
2
1
Advanced Monolithic Systems, Inc. 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140
1 page  
APPLICATION HINTS
This current is normally the specified minimum load current of
10mA. Because IADJ is very small and constant it represents a
small error and it can usually be ignored.
AMS1585
VIN IN OUT
VOUT
ADJ
VREF R1
IADJ
50µA
R2
VOUT = VREF (1+ R2/R1)+IADJR2
Figure 1. Basic Adjustable Regulator
Load Regulation
True remote load sensing it is not possible to provide, because the
AMS1585 is a three terminal device. The resistance of the wire
connecting the regulator to the load will limit the load regulation.
The data sheet specification for load regulation is measured at the
bottom of the package. Negative side sensing is a true Kelvin
connection, with the bottom of the output divider returned to the
negative side of the load.
The best load regulation is obtained when the top of the resistor
divider R1 is connected directly to the case not to the load. If R1
were connected to the load, the effective resistance between the
regulator and the load would be:
RP x ( R2+R1 ) ,
R1
AMS1585
VIN IN OUT
ADJ
RP = Parasitic Line Resistance
RP
PARASITIC
LINE RESISTANCE
R1* RL
R2*
AMS1585
Connected as shown, RP is not multiplied by the divider ratio.
Using 16-gauge wire the parasitic line resistance is about 0.004Ω
per foot, translating to 4mV/ft at 1A load current. It is important to
keep the positive lead between regulator and load as short as
possible and use large wire or PC board traces.
Thermal Considerations
The AMS1585 series have internal power and thermal limiting
circuitry designed to protect the device under overload conditions.
However maximum junction temperature ratings should not be
exceeded under continuous normal load conditions. Careful
consideration must be given to all sources of thermal resistance
from junction to ambient, including junction-to-case, case-to-heat
sink interface and heat sink resistance itself. To ensure safe
operating temperatures and reflect more accurately the device
temperature, new thermal resistance specifications have been
developed. Unlike older regulators with a single junction-to-case
thermal resistance specification, the data section for these new
regulators provides a separate thermal resistance and maximum
junction temperature for both the Control Section and the Power
Transistor. Calculations for both temperatures under certain
conditions of ambient temperature and heat sink resistance and to
ensure that both thermal limits are met.
Junction-to-case thermal resistance is specified from the IC
junction to the bottom of the case directly below the die. This is
the lowest resistance path for the heat flow. In order to ensure the
best possible thermal flow from this area of the package to the
heat sink proper mounting is required. Thermal compound at the
case-to-heat sink interface is recommended. A thermally
conductive spacer can be used, if the case of the device must be
electrically isolated, but its added contribution to thermal
resistance has to be considered.
*CONNECT R1 TO CASE
CONNECT R2 TO LOAD
Figure 2. Connections for Best Load Regulation
Advanced Monolithic Systems, Inc. 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140
5 Page | ||
| Páginas | Total 8 Páginas | |
| PDF Descargar | [ Datasheet AMS1585CM-15.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| AMS1585CM-15 | 4.6A LOW DROPOUT VOLTAGE REGULATOR | Advanced Monolithic Systems |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |