|
|
Número de pieza | CAT24C208 | |
Descripción | 8 kb Dual Port Serial EEPROM | |
Fabricantes | ON Semiconductor | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de CAT24C208 (archivo pdf) en la parte inferior de esta página. Total 10 Páginas | ||
No Preview Available ! CAT24C208
8 kb Dual Port Serial
EEPROM
Description
The CAT24C208 is an 8 kb Dual Port Serial CMOS EEPROM
internally organized as 4 segments of 256 bytes each. The
CAT24C208 features a 16−byte page write buffer and can be accessed
from either of two separate I2C compatible ports, DSP (SDA, SCL)
and DDC (SDA, SCL).
Arbitration between the two interface ports is automatic and allows
the appearance of individual access to the memory from each
interface.
Features
• Supports Standard and Fast I2C Protocol
• 2.5 V to 5.5 V Operation
• 16−Byte Page Write Buffer
• Schmitt Triggers and Noise Protection Filters on I2C Bus Input
• Low Power CMOS Technology
• 1,000,000 Program/Erase Cycles
• 100 Year Data Retention
• Industrial Temperature Range
• SOIC 8−lead Package
• This Device is Pb−Free, Halogen Free/BFR Free, and RoHS
Compliant
http://onsemi.com
SOIC−8
W SUFFIX
CASE 751BD
PIN CONFIGURATION
DSP VCC
DSP SCL
DSP SDA
VSS
1
SOIC (W)
(Top View)
DDC VCC
EDID SEL
DDC SCL
DDC SDA
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 10 of this data sheet.
DSP VCC
DSP SCL
DSP SDA
DISPLAY
CONTROL
LOGIC
D
E
C
O
D
E
R
S
ARBITRATION
LOGIC
1K X 8
MEMORY
ARRAY
DDC VCC
D
E
C
O DDC
D
E
R
CONTROL
LOGIC
S
DDC SCL
DDC SDA
VSS
CONFIGURATION
REGISTER
EDID SEL
Figure 1. Block Diagram
© Semiconductor Components Industries, LLC, 2009
September, 2009 − Rev. 6
1
Publication Order Number:
CAT24C208/D
1 page CAT24C208
I2C Bus Protocol
The following defines the features of the I2C bus protocol:
1. Data transfer may be initiated only when the bus is
not busy.
2. During a data transfer, the data line must remain
stable whenever the clock line is high. Any
changes in the data line while the clock line is high
will be interpreted as a START or STOP condition.
START Condition
The START Condition precedes all commands to the
device, and is defined as a HIGH to LOW transition of either
SDA when the respective SCL is HIGH. The CAT24C208
monitors the SDA and SCL lines and will not respond until
this condition is met.
STOP Condition
A LOW to HIGH transition of SDA when SCL is HIGH
determines the STOP condition. All operations must end
with a STOP condition.
Acknowledge
After a successful data transfer, each receiving device is
required to generate an acknowledge. The acknowledging
device pulls down the respective SDA line during the ninth
clock cycle, signaling that it received the 8 bits of data.
The CAT24C208 responds with an acknowledge after
receiving a START condition and its slave address. If the
device has been selected along with a write operation, it
responds with an acknowledge after receiving each 8−bit
byte.
When the CAT24C208 is in a READ mode it transmits 8
bits of data, releases the respective SDA line, and monitors
the line for an acknowledge. Once it receives this
acknowledge, the CAT24C208 will continue to transmit
data. If no acknowledge is sent by the Master, the device
terminates data transmission and waits for a STOP
condition.
After an unsuccessful data transfer an acknowledge will
not be issued (NACK) by the slave (CAT24C208), and the
master should abort the sequence. If continued the device
will read from or write to the wrong address in the two
instruction format with the segment pointers.
SCL FROM
MASTER
BUS RELEASE DELAY (TRANSMITTER)
18
DATA OUTPUT
FROM TRANSMITTER
DATA OUTPUT
FROM RECEIVER
START
ACK DELAY
Figure 5. Acknowledge Timing
BUS RELEASE DELAY
(RECEIVER)
9
ACK SETUP
Device Addressing
DDC Interface
Both the DDC and DSP interfaces to the device are based
on the I2C bus serial interface. All memory space operations
are done at the A0/A1 DDC address pair. As such, all write
operations to the memory space are done at DDC address
A0h and all read operations of the memory space are done
at DDC address A1h.
Figure 6 shows the bit sequence of a random read from
anywhere within the memory space. The word offset
determines which of the 256 bytes within segment 00h is
being read. Here the segment 00h can be at the lower or
upper bank depending on the configuration register.
Sequential reads can be done in much the same manner by
reading successive bytes after each acknowledge without
generating a stop condition. See Figure 7. The device
automatically increments the word offset value (8−bit value)
and with wraparound in the same segment 00h to read
maximum of 256 bytes.
http://onsemi.com
5
5 Page |
Páginas | Total 10 Páginas | |
PDF Descargar | [ Datasheet CAT24C208.PDF ] |
Número de pieza | Descripción | Fabricantes |
CAT24C208 | 8-Kb Dual Port Serial EEPROM | Catalyst Semiconductor |
CAT24C208 | 8 kb Dual Port Serial EEPROM | ON Semiconductor |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |